Search results

Hoping for some advice here. I have two cupboards under the stairs. A bigger cupboard that houses a fuse board and a smaller shoe storage cupboard. Both are separated with MDF but I can run cables between the two. The bigger cupboard houses a fuse board and already has a light and light switch...

Sorry, back again. I found my multimeter today (not that I remember how to use it :D). Can somebody advise how I test if this is active..... As in where do I stick the probes and if it's live, will it be live all the time or just when it's receiving a signal?

Good point.... I will check this evening. If it's anything like my current door though, the handle hits the wall first.

Will do. Yes, I understand that 100%. I meant it to read, I could just factor in a 25mm extender into the door measurements to play it safe but I'd prefer not to if I can, as I'd rather have a 25mm bigger door than the bigger frame (y)

That's great, I'm just waiting for Hormann to call me back to confirm the gap between the hinge and the edge of the frame. With this info, I should be able to measure and be sure. I am wondering if just getting a 25mm extension might be the smart thing to do anyway, although they aren't cheap. I...

Sorry, I realise this thread is going on a bit now but hopefully it may be useful for someone else anyway. I've checked the Hormann Thermo46 manual https://cdn.hoermann-cloud.de/fileadmin/_country/kataloge/pdf/85828_Thermo65_46_EN_UK.pdf?v=1599738547 and can see that the frame is 45mm deep off...

Thanks Crank, you've done a fantastic job of explaining that, I really appreciate you taking the time. This is a great forum! So, onto my next question..... Do most doors that sit in the corner require a frame extender? I measured my current door and the hinges sit 40mm from the wall, I...

I'm too tired to concentrate now but clearly, I don't understand the concept of the frame extender. Hopefully, it will all become clear tomorrow. Anyone fancy a trip to Southampton :D

Thanks, I appreciate your advice. Believe it or not, I am a fairly competent DIYer. I've fitted the odd window before and hung loads of internal doors. I will give the supplier a call tomorrow and check. I have measured many times and I even got the wife to measure, that way she can't blame me...

Cheers for the feedback, looks like I may have an easier repointing job on my hands instead.

Hi Conny, I agree but the plan was to clad the walls (after flattening everything out) with the stone shown in the image attached and the link in the initial post. To be fair, it would cost a bloody fortune, so it very much debatable as to whether it would be worth it. Because of the costs, I...

To be honest, I've given this no thought at all. Presumably, I can just fit a frame extender once I've got the door in place. Is this basically a piece of trim to finish the door and make good on the door reveal? Any idea on filling my gap? This is my current frame extender.

Perfect thanks for that. My other concern is the fact that you can bet your bottom dollar, my frame fixings will need to go through where the bricks join and where there is a slight void. Hopefully, I could bring the frame forward a bit or screw through the frame off centre but I don't know if...

Any advice? The wife is giving me grief about not ordering the front door

Hi Mr B, sorry if it come across like that, that's honestly not the case. I just always like to do the job right first time. Thanks for all your input on the thread.

I'm sure I read that duct tape, ironically shouldn't be used for sealing ductwork and the adhesive fails and causes leaks? What's the consensus on this?

That's great, thanks for your help, you have been very helpful.

So, I'm now considering a single 4-inch fan with dual extraction points with solid piping. I just think it'll be easier to work with. I get the vibe that everyone thinks 6inch is a bit overkill. Question about the solid piping. Presumably, any bends or joins should be welded via solvent cement...

Okay, sounds like I might be best off getting somebody into sort all of this as I can see me screwing something up otherwise. Wonder if there's anyone local that knows the Heatmiser systems, I'm in Southampton? So just to confim; if I have the wires/power from my room stat (if I need 4 wires...

Thanks, I will take a look.