Search results

Could anyone hazard a guess at this door handle make & model, possibly originally Wickes or maybe B&Q, purchased more than 12 years ago. Would be good to find a compatible plate outline and fixing centres. Looks a bit like Wickes Oslo, but the taper looks different. (Doors are 1930s originals...

Any thoughts about the likely causes of this crack in case it affects repair options? I have flooded the crack with superglue (the glass repair type) for now to hopefully prevent sharp glaze shards working loose. One may be evident in the photo just to the left of the centre grout line. Can be...

££££s - Yes, defo! The bungalow opposite me had this done about 10 years ago. I enquired about the prices at that time and IIRC £6k was mentioned. That didn't require any scaffolding though. I ended up using contractors to remove the flaking paint as much as poss, and repaint. They used some...

Thanks for all the suggestions. The hairdryer low/med setting was more than adequate. It was a muggy day so a bit of a head start. The dental floss would have worked but was a bit slow and needed a third hand. Ended up using an old AA plastic membership card (see pic) in a prying rather than...

The badge lettering obviously caught something (carwash?) and is now a potential flesh-stripping hazard. The pics show the stress lines in the top of the final letter making rework a bit problematic. Any suggestions as to the best way forward? Hot air gun and removal? Another bit of...

If you wanted to consider a more radical solution there's also this product, possibly as 2 or three terraces. To support the height, there are internal buttresses. I have used it for planters and border edging. I would use it again.... https://www.woodblocx.co.uk/retaining-garden-wall

Well you don't state the actual gradient (aka slope) so hard to visualise, but this might be a low cost solution... https://www.diy.com/departments/grass-protection-mesh-for-lawn-10m-roll-driveway-lawn-mat-car-park-turf-mud-reinforcement/5060164215882_BQ.prd along with a box of U-pins...

I am looking for a long-term 'direction of travel' for a choice of product, rather than a stop-gap. The results of a search here (manufacturer's website) suggest Rich Oak is no longer available from the manufacturer https://www.cuprinol.co.uk/product/cuprinol-less-mess-fence-care Google's AI...

It seems Cuprinol's Rich Oak is a discontinued product, available as surplus stock from perhaps less reliable sources. One reads about mislabelled and leaky containers. Are there any very close colour matches out there? Note that Ronseal's Dark Oak is too reddy-brown for my tastes, and looks...

I want to wall mount my collection (small but increasing) of Mountfield Stiga batteries which look like these... onto something like these, or functionally similar... Anyone done anything similar, and can recommend a specific Mountfield Stiga compatible product? Alternatively, which other...

Ooo - thanks for pointing out the slot in that threaded section. I missed that, but it's defo there!

My kitchen tap is over 12 years old. The internal sealing surface seem to be failing. I have changed the ceramic 1/4-turn valves several times, but after a few months a slow drip returns, i.e. from the tap nozzle. If a complete tap replacement is advisable, what are the DIY pitfalls? The...

I have one of these el-cheapo DIY outlet torches, and would like to get to the re-chargeable battery for investigation and replacement. It currently works for less than 30 mins between charges. It's quite a nice pocket size, so would like to get some use rather than binning it. This one is...

I have used reflective Solar Film to reduce solar loading in a utility room. It defo kept the fridge-freezer from working too hard. The see-throughness very much depended on whether it was lighter inside or outside. During a bright day, it was like looking in a mirror from the outside, with...

What screw fixings are used on a composite door, e.g. for a door knocker? The door construction is, apparently, 4mm GRP + 37mm PU foam + 4mm GRP = 45mm overall (related image from the Hurst website below), so not much bite into any thing solid using ordinary timber screws. The foam itself seems...

This is likely to be totally obvious to those who know, but what are the slots for? They are not apparent on the Mortice Type (and some types of the above). Thx!

Thx! The inner section is probably a bit gummed-up then. "... the bottom section may drop down and you may not be able to reconnect them...." Now that would be a bad day!

Any ideas how this low profile shower trap comes apart? It needs a good scrub. Does the middle part just pull out, unscrew, or twist to unlock. Or if the outer part unscrews first, does that require a special tool to get a purchase on those four tabs? All seems a bit tight otherwise. The...

I did a quick experiment with my jet washer, which seems to have the desired effect (see pic below) removing the blistered paint back to what looks to me like relatively sound render. A second pass is clearly needed before treatment and repainting. This was just a quick try. My question is how...

Answering my own question......these YT videos tell me all I need to know, and a lot more too about the fundamentally flawed design approach. There's an interesting improvement modification for those who are competent. My tri-wing Y-bit screwdrivers are on order for investigative purposes :cool...