Search results

Does anyone know if there is a sprinkler system on the market that you can fill up via an internal basin? Rather than using a hose? The tap I have is at the other end of the garden and was looking for something solar powered that you can fill up. Thanks.

Hi, The instructions for this are straight forward enough. However, the damn thing keeps going up in temperature irrespective of what I set it at. Does anyone have the same issue with this thermostat? And if so, any solutions at all? Many thanks in advance, Kris

Managed to get the flame symbol back on the thermostat, but the temperature keeps going up past the desired amount and the flame symbol goes off. There is a red light on the reciever within the bouler. I have tried switching it off, switching the power off at the mains, taking the battery out of...

Thanks Ian, Will give that a go. The instructions for this thing are a nightmare.

It's a RT510TX, with the receiver built in to the ETEC 33 boiler.

Thank you everyone for your help. The filling loop was quite a bit away from the boiler, but I found it thanks to your great help. Much appreciated. Now I need to figure out the damn Salus boiler receiver and thermostat. It won't switch the heating off now!

This is a diagram of the two taps I think are the filling loops

Hello, I am hoping someone can help me. I have just had a new ETEC 28/33 boiler installed. The pressure has gone down to zero and the filling loops aren't doing anything when turned. The radiators had to be bled and a lot of water came out. Would anyone know how to fix this please? Thank you...

Perfect info, thank you again.

Iggifer, thank you very much for that information. Are the unsiliconed ones easy enough to find out, do you know?

I don't recall asking how/if it can be removed, I was asking if there is a type of bezel without the glass, etc

Hello, Hopefully an easy one here. The downlights in my bathroom have packed in. I can't change the bulbs because a glass bezel has been installed with no other access to change them. I want to change them so that when they pack in again I can just remove the normal clips. Is this an easy job...

Gents, That's me finished the job ten minutes ago. Cut the new pipe down to size, arranged the backnuts and rings in order. A test found a slight leak at the outlet end, but tightened it up more and so far, so good. The real test will be the dishwasher and washing machine. Can't thank you all...

Sorry, it's most likely the way I have explained it The pipe that is currently being used for drainage is too short causing leaks. I bought a new 40mm outside diameter pipe but it is too narrow in diameter for the circular things (the ones I have a 40mm) that you tighten around the pipe when...

Gents, Happy new year and many thanks again for your help. Please accept my apologies for the delay in responding. I found that the waste joint was covered in god knows what, rust, dirt, etc that had formed a solid mass, covering it and not allowing the connector to go on properly. I also...

Hello, First of all, thank you all for your kind help. Yes, sorry the picture wasn't particularly revealing. The issue is at the lower joint where the compression elbow meets the black waste joint. The black waste joint is actually starting to rust. Have any of you had any luck repairing a...

Hi, Sorry if this is obvious, but I have read the Wiki and the FAQ and can't find an answer. The last trap (there are two after the pipe) at the end of my sink waste pipe has came away from the outlet at the wall. It looks like the trap doesn't quite reach the outlet far enough to fit tight...

That is great news that it is a straight forward job. Listen, I really cannot thank you enough for your help there. Thank you very very much.

A thousand thank you's sir! Are these handles relatively easy to fit? In terms of making sure the lock that pops out to open or close the window fits in with the new handle? Many many thanks again. Kris

Hello all, Really hoping a kind stranger will be able to assist me. The handle that opens my bathroom window has snapped off when closing it one cold morning. It is housed in a timber window frame. My problem is that for the life of me, I cannot find the correct handle anywhere online...