Search results

We Have very bad stains on our conservatory roof from the lead flashing. It's not the white stains that I have read about but a dark stain coming from the lead ridge and from the velux windows. They have been there a few years at least. Have tried a pressure washer but I think I'll need some...

Sorry but have another question! in the kit there are two large washers one rubber and one Plastic. The only place these are mentioned in the instructions is on the outlet connection. My problem is that the brass tank connector already has a rubber washer on it? so should I discard the other...

False alarm! I went out to look at the tank/cistern again and felt inside and they do not go the whole way through they actually extend into the tank like a tube.

I wish I had the height mate ;( I got the new one today but am a bit puzzled, there are two 8mm holes pre-drilled about 35mm from top at both ends so 4 holes all together ? If I were putting any fittings like ball valve or overflow at those positions the holes would be very awkward. The...

Unfortunately that one was too long, it wouldn't fit in the space available. Cheers

I just ordered one from screwfix now. Its 1190x610x500 500mm is the width of my loft hatch so I think it will go through this is the only one that would fit as far as I can see so in the end didn't have much choice. Even the smaller 44gallon one was 503mm and I didn't want to chance it. Thanks all

hi I have a leak in the bottom of my loft water tank, I think it's a 50 gallon one but I'm not sure. The measurements are 45inches by 23inches wide,23inches deep It's going to be really hard to get it out and to replace it as it seems to have been built into place I might get it out if I remove...

Ok thanks for that. I'll ask my local plumber if he can do it. Thanks again Mike

is there any way apart from having a combi boiler fitted that I could do away with my large loft tank that supplies the hot water tank in the hall. I would have thought that someone would make a device that that could reduce the pressure enough to supply the hot water from the mains. I know...

Yes sorry I'm a human being. what are you ? a C**** obviously

Thanks I didn't give anyone enough time to answer really as so often happens I persevered and found the answer myself in half an hour lol. I'll have to have a look at the easy access ones though, are they really easy ? I have just found the SaniAccess3 which looks like it might do the job but I...

Update: For anyone in the future who might have this problem. I think i have it sorted! I did need to pull the rubber pipe out more,it was very difficult as there is nothing to get hold of. After getting it out to the next lip it still wouldn't let me push in the elbow so I tightened up the...

HI I am trying to get the lid back on the saniflow and it has a nearly central black rubber discharge pipe that seems to fit flush with the Top . Into that there is an large elbow which takes the waste away. I have the lid clipped on but... When I try to push the elbow down into the rubber pipe...

ok thanks will have a go tomorrow.

mmh how do i do this?

Hi Hope this is ok [/URL][/IMG]

Hi we have had a lot of problems over the years with a saniflo Macerator so a couple of years ago we replaced it with an industrial one. it is only in a spare room so does not get used much. This morning it jammed on and my wife didn't turn it off from the mains so it was pretty hot when I got...

HI again Fitted the photocell this morning. Boiler fired up first time! :D Only problem was the way they had run the wire from the controller. It's impossible to pull it out ! It's been fitted obviously before another part (maybe the pump I'm not sure ) and the 2 way connector can't get through...

Yes that's the one. I've ordered a photocell . I''l let you know how I get on. Thanks for your help Mike

I think it was last summer so it should be ok, when I look in the hole where it goes it all looks clear. I probably should get it serviced anyway I suppose ;( I will change the photocell anyway as that's so easy. Does the other end of the wire just pull out or do I need to unscrew something?