Search results

Door interlock is prime suspect. Try putting some pressure against the door when closing it to start a programme if this starts it replace door interlock and also make sure the door latch is hitting the interlock opening centrally

I think you will find the back does not come off on this model.Access is from the front so you will have to remove the front panel.The only other way is to tip the machine back as far as you can making sure it is well supported (make sure you have emptied the drum of water by hand before doing...

examine the retaining ring all around you will find at a point on the wire ring a spring connecting both ends of the ring.Using a small thin blade screwdriver lever up and pull forward under the wire close to the spring to disconnect retainig ring from door seal

Well thankyou both, your feedback is appreciated, Happy Viewing

No just the channels that come up with no or incorrect channel number when entering your videoplus code which was just bbc1 and channel 4

ok last step you now have to re-educate videoplus. Start with putting a videoplus code in for a channel 1 programe which I assume is bbc1. when you enter the the code the start time, end time, date, etc will show in the table. were it has programme number it will be blank. (or it may be E1 not...

Once you are sure all your channels are tuned in bbc1 bbc2 itv channel4 and you can confirm this by selecting the tv to your video channel on the tv remote control usually channel 9 or channel 0 if not connected by a scart lead.Then select channel one thru to 4 on your video remote and each...

I think I can pick the bones out of that. If I am correct If you programme a videoplus on channel 2 or 3 it is ok. but if you proggramme a videoplus programme on 1 and 4 it shows E1 or E2. If this is correct it means you have lost the tuning setting on channel 1 and 4. When this happens your...

You have accidently programmed your video to record off input E1 and E2 are indicating that the video is set to record timer or manually off the scart sockets at the rear of the machine as opposed to your channels 1 2 3 4 and possibly 5 if you recieve ch5 terrestially. Two things to try 1...

ok well that would eliminate the cold water valve and if the door lock is definately indicating closed I would now be suspecting the programmer or if electronic the pcb, but because of the large cost of the part it may be time to call in an engineer were he could diagnose with the aid of...

one possibility is the cold water inlet valve is open circuit. It is possible it stopped and went open initially on the rinse cycle. You can test with a cold continuity ohmic test across the terminals of the water valve.Before testing try a boil wash programme if this starts but stops on the...

Generally you do not have to take apart the water pump to inspect it. Disconnect the inlet and outlet pipe,remove the pump fixings were it is secured to the washing machine, take out and you should be able to see down the inlet and outlet openings to the impellar were it is very common to find a...

check with a multimeter set on ohms this reads through the thermostat to confirm there is a current path intact. The reading when you check each thermostat should read low ohms if it reads high or infinity the thermostat is open circuit.

Unfortunately I fear not in pre- modern tv,s the be all and end all was the scart socket which was the modern way of connecting all inputs into the tv as the scart plug had many connections all inputs were covered in this multiplug and the user would just enable the tv via the remote control...

ok just looked up the specs for this model and it states that there is a seperate s-video input connection on the tv. It is possible it may be within a flap or door somewere at the back of the tv this is why you may have overlooked it, this being the case it would only require a s-video to...

Just turn off the hot tap (red handle down 45 degrees disconnect the washer hose and fit blanking cap on the end of the valve you will need a 3/4 inch BPI blanking cap to eliminate the valve being accidently turned on. Plumbers merchants or possibly b&q would stock.

Yes try the other scart socket on the tv if that does not work refer to the tv user manual under av input chapter and it should tell you how to enable scart sockets to accept s-video input.It will only be a setting you configure with your remote control. s-video input is a combination of two...

just clarify that your first statement is the dvd player does not have a scart socket but yor last statement asks whether you should use the other scart socket on the dvd player.

You have a mismatch between your output signal to your input signal. Your tv scart input will usually default to composite signal input which would come from your dvd,s scart socket to your tv,s scart socket. You would then need a scart to scart connector. The other option and maybe the simpler...

ok just to pre- empt sleepyheads reply stand pipe is a fixed verticle pipe which is plumbed to outflow into your drains, and your grey water outlet hose from your washing machine slots loosley into this fixed pipe spigot fixing is were your grey outlet hose from your washing machine is...