Search results

  1. it's not that hard

    Bathroom quote

    you must be slow then if you can't change a wc,basin and bath in less than a day,I won't take off the old tiles,make good any holes or fit the bath frame/panel and no tiling,costs about £30 to £50 for 5x flexis and 2x waste flexis if needed and a pan connector = 6 hours x £50 = £300 profit, how...
  2. it's not that hard

    How can I turn this radiator valve off?

    you will be lucky to turn that, someone has already snapped the square top off, but give it go use wd40
  3. it's not that hard

    Drain cock on 8mm pipe

    get a radiator valve with a built in drain off,would have thought there might be one on there already https://www.google.co.uk/webhp?sourceid=chrome-instant&ion=1&espv=2&ie=UTF-8#q=8mm%20radiator%20valve%20drain%20off
  4. it's not that hard

    Central heating drain valve

    could have a primatic cylinder,did you just shut off the water and open the hot taps or drain it with a hosepipe, you might have a gravity system are 2 of the pipes that come out of the boiler bigger than the other two
  5. it's not that hard

    Bathroom quote

    Should have posted a picture,have you got a combination boiler,if so you could put on thermostatic bath/shower taps costing about £80,that would save money. I charge £350 for a standard bathroom replacement including plumbing parts,takes a day,I don't do tiling why pay plumbers rates when you...
  6. it's not that hard

    Can someone help me locate a mixer bath tap?

    Are you sure that they are 6" centres ?
  7. it's not that hard

    Help for a novice - Leaky join for the washing machine hose

    I would change the valve,turn off the mains stopcock,unscrew the hose,check there's a rubber washer in there if not buy one, undo the compression (silver) nut,fit the new valve and check joints
  8. it's not that hard

    Pumped shower problem

    I hate showers and never get involved with them,electric,gravity,pumped,thermostatic,mixer,concealed,shower trays,wastes,doors,all a pain in the f*****g arse,just glad there's keen plumbers like you,thank you
  9. it's not that hard

    Combi Boiler Main 30 HE - how do I increase the pressure?

    Look under the boiler inside it,there might be 2 valves to connect the hose,otherwise probably below the boiler, but as you said you need a hose so will have to buy a filling loop hose
  10. it's not that hard

    Removing a radiator

    The problem is where will you get a decorators cap without buying a new trv,so get a 1/2" blanking cap and put it on the end of the valve,you do need to cap it as they are designed not to shut fully but sometimes they do...
  11. it's not that hard

    Concealed Geberit Leak

    WOW can't get much better reply than the one above and you don't have to use your hands,technology EH
  12. it's not that hard

    Concealed toilet system - Tece/Grohe/Geberit

    I have only replaced a Grohe adiago,fitting a concealed cistern is a piece of cake,it's when you come to replace it one day, after the carpenter and tiler have entombed it,so I was impressed how easy it was,took about 10 minutes
  13. it's not that hard

    Toilet not flushing unless AAV pulled off

    I had this problem in a downstairs wc in a new build,drains weren't blocked, left a hosepipe running down there for an hour,told them to refer back to the builders,there was no way either to redirect the pipe outside as there was no outside wall by the wc,
  14. it's not that hard

    Merkel is being trashed in the elections...

    Neither does a politician
  15. it's not that hard

    Stopcock. 2 taps on same feed, the 1st needs replacing rough cost?

    That's what I said as well newboy, you can see a drip on the top stopcock,looks like money might be wasted there,you and I know, say if a wc is leaking they always say it's from the pan connector when usually the water is dripping down on to it.
  16. it's not that hard

    Stopcock. 2 taps on same feed, the 1st needs replacing rough cost?

    The top stopcock is leaking from the gland nut,which is the first nut by the handle,this can be repaired without turning off the water, undo the nut,wind PTFE tape around the spindle get a small screwdriver and push the tape in deep where the nut screws in and screw back up,don't know about the...
  17. it's not that hard

    Stopcock. 2 taps on same feed, the 1st needs replacing rough cost?

    The top stopcock is leaking from the gland nut,which is the first nut by the handle,this can be repaired without turning off the water, undo the nut,wind PTFE tape around the spindle get a small screwdriver and push the tape in deep where the nut screws in and screw back up,don't know about the...
  18. it's not that hard

    Smelly internal bathroom - Soil vent pipe problem?

    Apologies, yes you are right about the 70mm gap
  19. it's not that hard

    Smelly internal bathroom - Soil vent pipe problem?

    you should have went to spec savers,anyone can see that's a 110mm pipe and it's blatantly obvious it's fully fitted,I think that you can't see an easy way,wouldn't want you to work in my home if you want to make a simple job into a long winded exercise maybe take up stamp collecting instead...
  20. it's not that hard

    Smelly internal bathroom - Soil vent pipe problem?

    The AAV is a pushfit,pull it out and the rubber washer,can you reach it,If so what I would do is get a 110mm flexi pan connector,fit the AAV into it and push into the pipe,save hacking off tiles and could e just a 5 min job, flexi pan connectors come in different lengths. This way you would...
Back
Top