Search results

I did buy it as a kit but there are no plug in modules in the control panel. I have wired in a separate texecom speech dialler which I have run the test menu and all works fine, but it won't talk to my control panel, however I have altered loads of settings in the panel outputs, comms outputs...

I think the premier 24 has both 2400 & 300, I am not sure what setting on the control panel operates the speech dialler is it the digi com / com 2400 / com 300 I am finding it very confusing. I have spent ages on the net but I canot find any decent manuals / information to help me set this up.

I will check the outputs, on a separate note when anyone rings the landline they get the modem 'squeel' and cannot hear us, I have dialled our number using my mobile and also got the modem 'squeel' but I pressed 8 and it stopped, do I need to increase the number of rings?

Finally got the speech dialler configured and the tests mode works fine, I even receive text messages. When I arm the alarm I get a phone call telling me the alarm has been activated? which is the message I configured for alarm activated. When I set the alarm off the speech dialler does...

Every time I try to configure my speech dialler, about halfway through the programming and testing the unit locks up, it will not allow me to enter the pass-code it just does nothing. I have removed power from it and reset it it a number of times but the same thing keeps happening. Could it be...

If I remove power and battery will I retain settings? Do I need to kick start battery when I restore power?

I have just installed my Premier 24 Alarm and finally got it all working, I have spent ages setting up all the configurations and entering text, but it all works. However I have a problem with the speech dialler which I now need to configure this problem has now happened a couple of times. I...

I get no texts at all, I do hear the modem and then a message saying failure to connect. The telephone line is plugged into the same box as my Wifi Router and is plugged into a filter? Dave

Finally got my system working, can I thank everyone who gave me advice I wouldn't have done it without you. Having problems with speech dialer sending text messages, but after a bit of research I see that this is not uncommon, I have quite a few suggestions to follow up on. I receive phone...

I have finished all the wiring of my Premier 24 with 11 PIR wired (EOL) expander, 2 keypads and speech dialer. I have managed to remove ALL alerts on the keypad, Bell Tamper, & Auxiliary Tamper. I have done a walk test ALL OK I have done a bell test ALL OK The problem I now have is...

When you say check the tampers?Do you mean the actual switches, if so how can these be checked? Or should I just bend the actual contact so it makes a firmer contact? Safe Dave

I am no expert, but I am sure that if you have someone stood next to the control panel / keypad. and when you remove the bell box cover which may set the alarm off you just type in the engineers code and that will stop the alarm? and allow you to do the changeover, it may happen again when you...

I have just wired in my Premier 24 - which has 11 PIR wired (EOL), 2 keypads, 1 zone expander, 1 speach dialler. when I powered up everything appeared OK, I have done a walk test and all the zones worked. However I have 2 faults 1 Auxilliary tamper circuit fault ( I have connected the...

Can someone give me advice on how to wire the texecom speech dialler into the premier 24 control panel. I assume 0v 12v are power connection Tamper wires into the control panel tamper circuit, which is not used (EOL wiring) I am OK with the phone connection But I am struggling with...

Thanks for the help re PIR I have taken advice and purchased a zone expander and will be giving each PIR it's own zone. On a separate note I have a Texecom Premier 24, with 2 remote keypads, I know how to wire these into the control panel / expander. The keypads have connections for zone 1 &...

I have wired in alarms before but I have not done EOL I think I understand it but can someone tell me if what I am doing is correct I have PIR with jumpers which can be set for EOL resistance, which I have set. So do I now but one wire into the alarm circuit (if so which terminal) do I...