Search results

Hi, Id really appreciate a bit guidance on how to wire this dimmer module. I have 1mm TE coming in from the lighting circuit and then another 1mm TE running to my LED lights. Could anyone advise on which live and neutral goes where? Thanks in advance

Sorry but I think this thread has gotten a bit out of hand. I would be grateful if anyone could advise me whether I can add a 50a RCBO paired with a 10mm2 TE cable to power a 7.3kw EV charger, with the cable routing adjacent to my floor joists in between floor boards and the ceiling below. I...

Yes, that's very true. Given my next car is a 4 year lease, I'm happy to go down an intermediate route by having a 7kw charger running off my CU and in the future when I have my driveway done, bury a cable that can we used for a future high powered charger in case I go down the full EV route. As...

Thank you for the advice. Im not sure i follow the usual bandwagon comment? Also why is a PHEV a bad idea? Most of my driving is 20-30 miles and I don't want an EV for the longer runs.

Hi, I don't plan on getting a full EV, but do have plans to get a PHEV with a 33kwh battery, which using a 7kw charger would be enough to have the battery charged overnight everyday. I won't be fitting it myself but wanted to check if it was feasible to add a dedicated circuit to power a 7kw ev...

Thank you for the detailed reply, but I just need to know how to join the two connections together. It is the brine waste outlet and there is no recommendation to fit a tundish from the manufacturer. If it overflows, then the overflow outlet will dump the water and as long as there's no leak...

Bumping this to hopefully get some guidance. Thanks

Hi, Hopefully a fairly straightforward question. I'd really appreciate some advice on the best way to connect the waste outlet from my water softener (as pictured) to the pvc pipe my kitchen fitter installed for me. I want to make the connected demountable if I ever need to change my softener...

The downpipe needs to have the drain changed slightly right? Also would it be a good idea to add another drain under the tap and connect them to each other?

Hi all, I'm having the area in the photos tiled with porcelain tiles. Previously it was gravel and and would drain into the soil underneath. However, I'm wondering if there needs to be a drain put under the outside tap that then connects with the drain that the downpipe connects to? Also how...

Thank you folks, I'll go with a 13a FCU :) Much appreciated!

In the past I got advice from the forum that a 20a DP switch would suitable to safely isolate external lights as the circuit is protected by an RCD at the CU. Would this negate the need for an 13a FCU? If not, I can fit that instead.

Thanks Andy. I'll have a go and see how I get on. I'll also consider dropping down to 1.5mm2 as you're 100% right.

No, 2.5mm T&E for each conductor as this sits inside my garage. Two clusters are fence mounted so I'll be using .75mm flex to loop in and out. The 3rd cluster is in flower beds, so one 2.5mm T&E will connect to a weatherproof jb mounted on an exterior wall, from which an SWA cable will be buried...

yes, it's RCD protected at the CU.

Hi, I have a dedicated garden lighting circuit in my house and I am adding 3 new lighting clusters (35w lights, with 5 or 10w GU10 bulbs, total of 18 across 3 clusters). I would like to power all three clusters from single 20A DP switch so I can isolate these clusters in the case of faults (1...

Based on this, a .75mm2 cable should also do the job right seeing as it's rated for 6amps which is considerably oversized already?

Yes, sorry that is the rating of the light fitting. I'll probably put 5 or 10w bulbs in them.

These will have LED bulbs but I'm not a huge fan of LED Strips

Hi, I'd really appreciate some advice on the right type of cable to wire in 6x 35w GU10 spotlights that will be mounted onto a wooden fence. I already have a dedicated garden lighting circuit and will run the connection via a 20A DP switch. Ideally I'd like the thinnest cable possible as I need...