Search results

Do I just need to change the fuse? Or do I need to change the fuse and replace the old busbar to the left ensuring the the two seperate section do not meet. Also if I have to remove the bottom (make do) busbar do I remove only this as I can see a large red wire in the background.

cheers for advice and help all please keep it coming John, Yes I still have the black thin plastic cover that shields the bottom half of the fuses (where the copper plates goes) I may come back to you about the replacement fuse. As i see it as long as the power is off it is just a...

How could I put the correct copper plate back would I have to use the following circled platic grip and place back where the arrow is shown? Is that all that hold the copper bar in place / connecting to the other copper bar? Cheers for advice

Well here are the pictures, Please keep the advice coming This is a picture of copper plate This is the unit 154 Shows the replacement of the copper bar. Any thoughts / advice Coops

Hi Today I had a electrian come and fit our new shower, and cable. After he left there was a polished copper bar similiar to the top of a castle wall about 4 inches long left near the consumer unit. Looking at the consumer unit the electrian has used a different make of fuse than the...

Please help, I am trying to put a light in the loft from the lighting circuit. I have looked at the lighting circuit from existing roses on the ceiling upstairs. As the house is just 10 years I assumed that the wiring would be loop in wiring. But upon looking at the roses and all of the 4...

Hi didthathurt / all Thanks for advice, I have so far remove one twin socket in Bed 2 from the JB and made this a spur from an existing socket ~(still going via the loft up and over). I have looked at the lighting circuit from existing roses on the ceiling upstairs. As the house is just 10...

hi jj4091 Cheers for comment. I have not done this I have found this out when boarding part of the loft. I have been looking through the large B&Q book and it states that if you have difficultly getting to a light power cable you can as long as it fused connect to the mains. This is where I...

Hi I have not long moved into a house, and have found the following: In Bed 3 there is a twin socket that is on the ring main, from this there is a twin socket on a spur into the next room (Bedroom 1). From this spur the cable goes up into the loft and into a 4 way junction box. From...

Cheers for advice sime10 The reason I need to add another layer of silcone is because I ran out due to needing to apply a large amount within one section. This then caused me to get a the best finish possbile. It look good managed to seal all the way around, except. The problem is that the...

Hi I have been using silcone sealer for my bath and am wondering if there are any issues with applying a second application on top of the first one once it has cured completely? Cheers for help in advance Chris

Softus Cheers Both the main and small tank have pipes that go above the lid and then pop through the lids. The vent I would think in the overflow pipe that leads to the outside wall? The small header tank is the typical square type. Do you have any ideas were I can find a lid elastic...

Hi Softus What I though I would do is to correct the few things that the surveyor put in his report. Otherwise all I know is that when I went into the loft the other morning after a night of frost the black fabric that is underneath the roof tiles was wet to touch (never seen this before)...

Softus I asked for advice on this forum about the wet black fabric that was in the loft, and one of the possible causes was to make sure that the water tank lid fitted, now since I have only been in this house for 3 months and that our surveyor highlighted it as well in his report I therefore...

Hi I have been trying to locate a round water tank lid for the main cold water storage tank in the loft, due to non correct fitting lid that is currently causing alot of condensation in the loft. Any ideas or suppliers / manufactures ?? There is not name on the tank, only one on the lid...

Third_Eye Many thanks for your help. Had to look up the word Gyproc but I found the filler. Cheers Chris

Many thanks for the advance, I know the water tank lid is not the orginal, I will have to look for some type of elastic one or see if I can still get the original. Cheers Chris

Hi Richard Thanks for the advice, sorry it took so long to get back. The doors have not adjustment on them, the centre bar is part of the other side of the door. Cheers Chris

bab Many thanks for youy help, worked like a treat Chris

HI Thanks in advance for all advice received Hi, I have just been in the loft this morning after an frosty night / morning and the black kind of fabric layer that the tiles sit on is damp. Well what I mean is that when you touch the black material it is wet to touch. Is this...