Search results

By the statement below do you mean that i should use two cores for 2 and 5 and two cores for 3 and 4 How many cores are their in telephone wire? Make sure you use a pair for 2/5 and a pair for 3/4. Thats Blue/White White/Blue and Orange/White White/Orange.

I with ntl and want to add a new telephone socket from the master socket. The master socket has a removal lower part with the terminals 2,3,4,5 The new extension socket has terminals 1,2,3,4,5,6 Do i just connect terminal 2 of the master socket to terminal 2 of the extension socket and so...

I have a hoover WDM120 which is not taking down conditioner on the rinse cycle. Water is entering condition compartment and the hole in clear if i pure water into the conditioner compartment it will flow into the machine leaving the conditioner compartment empty. Should their be some type of...

Is their any trick in putting back a kickboard from under the kitchen cabinets seems to have grown since i removed it. or do i have to file it down a bit.

I have a WMA washing machine When turned on and cycle selected it fills with water then the drum goes into spin speed immediately for about 5 seconds then stops This is on a non fast colour cycle. I can also here a load scraping noise coming from the motor. I have checked the harness and also...

No Its an F04 error pressure switch stuck on empty.

Is the machine taking in water? Check the waster supply Then check the water valves

I have a WF540 1400 spin Which keeps stopping in cycles. The light is flashing error code. pressure switch stuck on empty What should i check?

I have a Creda Washer dryer which doesn't Take conditioner on cycles A To E. The machine will take conditioner only on cycles F to J I notice on the dial, cycles F to J have a conditioner symbol and cycles A to E do not. All cycles A to J have a rinse. I had a look in the manual and the...

I think this machine has an anti flood device. Which is a float located at the bottom of the machine. check the float. Make sure the water is not just flowing out of the waste pipe because the pipe is to low.

I have a WM washing machine the front bearing has collapsed leaving the outer part of the bearing stuck in the outer drum. I tried hitting them out with no success. I purchase a bearing puller on Ebay, has anyone tried using a bearing puller to remove the front bearing? Is their any other...

I have a Kenwood KVT1W Tumble Dryer two of the resistors are burnt out the tumble dryer works but you have to keep the on button pressed. On my ohm meter I selected 200K and the reading i got displayed on my meter from the two resistors was 32 does this mean that the two resistors i need are 32...

When replacing the bearings on a whirlpool AWM1404/4 Do you also need to replace the tub seal? is it also a good idea to use Universal Bearing Seal Sealant Grease on the shaft?

Do anyone have a list of error codes of an indesit WIL132 Thanks

We are breaking down machinces i would like to ID the parts and find out what other models they will fit

On many online websites that sell washing machine parts you type in the model number of your appliance click search and it brings up the part details for that model and what other models the part fits. So if i done a search for a motor for a indesit widl126 it will tell me all the models that...

On a lot of these machines i have come acroos a short on the interlock between live and neuaral on the door interlock

They have the details of the manufacture and and digits on the top So your saying from the labels on the motor i wont be able to find out which machines the motor would fit their is no information available to me If i was to take motors from old machines and log the make and model of that...

Keep the door open turn the machine on then close the door if it trips immediately when the door is close i would say its the door interlock. Interlocks are cheap to buy. Do you have a muitimeter?

I purchase a job lot of 150 washing machine motors They are from mixed washing machines mainly bosch hotpoint and indesit none of them are in their packageing Is there any way i can find out the part numbers for these motors and what models they will fit so i can store them