Search results

Hi i have set tout some pavers for a patio and i can only get them smack on the dpc .I am just worried it needs to be lower, but this means quite a big job . Can i put some DPC along the wall and under the pavers , or is this a no go .Any help for me regards

thank you thats what it will bee

i have a run of worktop 2metres and one of 1 metre i need to butt joint to a good snug finish ,reason for the joint is the kitchen wall is 3" further back , so one small bit sticks out the 3" at the bull nose with a bit of edging stuck on .Am i best routing it or circular saw from the...

6mm twin core and earth 30 amp fuse Had this for some years now

I need to fit a new one , can only go to 8.5 with current set up .What i need to know is are they all the same basically or do you get what you pay for . You can pick a Triton up for £60 and then pay £125 if you fancy . Its not finish i want just a decent heat /flow Reading reviews some...

The water inlet on the lecky shower ive just bought is plastic no thread im guiessing it needs one of them fancy joints ,so i take of my old compression joint on my 15mm feed and put what on . im old school thanks nobby

Yes thats what i used a thin coat of water resistant PVA THANKS JOB DONE

i have my daughter kitchen floor to relay in a pretty good qualty laminate "clic " type Is there anything i could use prior to fitting that will hold out any water spillage that makes the stuff swell i have thought of wiping over the edges with WD40 or a bit of good car wax or silicone...

thanks for the reply i have done it and all is fine now I NEW I WASNT BEING VAGUE LOL

how do you square up the little hooks in the headrail i have a couple that are quater of a turn out compaired with others regards

IDEAL LOGIC 24 .The central heating is working fine, just the hot water running from hot to luke warm conitinually Any suggestions please B

its a floorboards .It is going to be noticable the dip is in the part of the bedroom that is viewed as you stand at the door , i believe if is caused by previous owner removing dividing wall downstairs to create a "through lounge That said i will try as you say to pack with ply

i have a bedroom floor that is is dished in the middle . What is the best way to pack it out to get a reasonably level start to lay T&g laminate floor its about !/2 inch lower in the middle ,with a straight edge

im a bit wiser now im thinking put the Mag on the top first right upto the edge ,wipe of as suggested, gloss white Dado should be bit easier been less of contrast last paint the bottom , dark colour

good points there I reckon i will try your way on one bit of upstairs wall and try masking gloss rail next to it and see what gives thanks for your views Have we a damp cloth the current wife please

got a full HSL with white dado ,lined out and ready for magnolia top part and lets call it mocha bottom in matt emulsion ,Dont know wether to gloss rail first then mask and emusion , or tuther way round thanks indesisive Dave

i have a standard Parkinson Cowan gas cooker and the grill has started making a howling noise on full gas . Goes when i turn the gas down Is it serious or "sortable" regards

is there a bit that would sink wood and mild steel for eg opening up hinge countersinks seen hss and titanium any advise please

I have a HSL to do that will be finished with lining paper . i have used Johnsones paint in the past . I cant make my mind up on the finish , wether to go with vinytl matt or there soft sheen . Thing is i cant cope with wavy wall reflections though i will prepare as best i can . Or will the...

Thats what i was thinking of using Johnstones coverplus Dont want to appear rude ,could you tell me why you would put a coat of whit on first instaed of magnolia which i think is the same price Is it to "knock" the colour out of it