Search results

cold

ok cool thought as much, thanks what a headache... next time wet underfloor heating system!

Hi there Got a problem with my electric underfloor heating that my builder installed in 2013 It's a Heat Mat installation below tiles, controlled via a KNX switch that turns it on for a set amount of time (via a KNX actuator). It's in the bathroom but there doesn't seem to be any cracks in...

thanks very much - will change that!

hi all quick question to check why this entry time isn't working as expected in my garages. so Area A is set as a Timed Exit, Entry 1 Delay Time and Entry 2 Delay Time are set to 120s. Area A has a: garage door contact set to Guard Access a PIR set to Guard Access and to Double Knock too a...

Thanks for the help everyone The replacement battery arrived before I had chance to sort out the multimeter and everything looks like it is working fine now... looks like the previous battery, even though 9 months old, was knackered

No I haven't measured any of that stuff. I'll buy a multimeter and see what they are. Strange it would start happening out of the blue, the devices on the system haven't changed for a long time.

Yes I think you're right maybe not the battery. I will check the jumpers this evening but quickly in the morning I checked the logs and I had low voltage warnings expanders 2, 3, 4 overnight. This is without the "faulty" battery connected. The fuse it not lit red but I guess I will replace it...

Battery terminals were fine. It's been working fine for 9 months, nothing touched it. It is a Texecom PSU200. The battery is the same model as the original installer put in the main alarm box so I bought the same when I added the extra PSU What I didnt understand is normally if the battery is...

Fuse in PSU 2 was not lit red but the battery fault red light was on. For the time being I disconnected the battery and will order a new one

So just now my alarm went off out of the blue whilst I was in the house, put in code and there were a bunch of items. I downloaded the log and it looked like earlier today in the afternoon there were some battery issues too: ... The system is configured with a battery in the main box and...

OK cool thanks, that makes sense Texecom said options 26 and 27 only apply to full set, but what happened here is as you say contradictory to that - which is what had me a bit confused!

Hi there A little mystery... not sure what's going on here. Premier 48 panel and Part Armed overnight When disarming system in the morning I saw that a zone had been active overnight on the keypad. The logs: So what exactly does this mean? I can't remember hearing the internal or external...

It looks like soon you'll be able to integrate Texecom directly with Z-Wave and a bunch of other stuff: http://www.texe.com/uk/technology/connect/ A more expensive option is Control4 (although if you buy a second hand HC250 controller off ebay and find a cheap integrator it's not ridiculous)...

So reply from Texecom (very promptly I must say, excellent service): Configuration 26 and 27 only apply to full set operation, part sets will operate as normal even with these options enabled. As a workaround for this you could either turn your part set into an area or use the beam pair...

Yep I have set the digi output for thee text/speech dialler to trigger on Confirmed Alarm, and I didn't get a text. I doubt I got to the keypad before it managed to dial and connect to the SMS centre too. Option 35 is worded like this in the manual (it's not clear if you tick it which on of the...

yes a bit confusing... I take it's nothing to do with option 35 being checked?

It was the internal sounders for sure, don't know if the external bells went off too

hi there had an issue a few days ago where one of the PIRs in a garage was triggered by something moving in the garage, which caused the alarm to go off. The garage door, which has a door contact on it, remained closed. Both the PIR and the door contact are set to guard access. I was expecting...

Thanks Part Arm Coms was empty... I've added the zones to that now "Bells on Confirmed Alarm" is indeed selected. So in this example, the alarm didn't go off because the same PIR (or any other) was not triggered twice within the confirmation window, but the keypads kept beeping all night...