Search results

Yes there is a loft space above, but there is a button on the receiver for programming (if needed). Switches are pre programmed. There are 2 doors into what used to be a bedroom, but now a utility room (no plumbing). Could I use a surface mount single socket box in place of existing light rose...

I want to fit a Dewenwils light switch kit as a 2 way system instead of wiring in an extra switch. I have found that the receiver is bigger than I anticipated. The receiver will not fit inside my existing light fitting and the existing wall switch is a switched live plus earth only, so I would...

A Google search gives this result. Increased volume with an RCA connection is generally represented by an increase in the voltage of the audio signal transmitted through the cable. The higher the voltage, the louder the sound will be at the receiving device.

Technics (SA-EX120) Frequency response PHONO RIAA standard curve (30 Hz-15 kHz) +-0.8 dB CD, Tape Monitor, VCR10 Hz-40 kHz, +- 3 dB Input sensitivity and impedance PHONO3 mV/47 kohms CD, Tape Monitor, VCR200 mV/22 kohms Signal-to-Noise Ratio at rated power (8 ohms) PHONO70 dB (IHF, A:80...

Is it the RCA output voltage that is critical? If so, the RCA output of the Neotec DAC NTK003-IT recommended is 2 volts. As I need Bluetooth, could I use this...

Lucid Thank you very much for your help, much appreciated. I am using a Roku mains/USB adapter rated at 5volts 1 amp. So it seems the Prozor is not suitable. Do you think this would be any better https://www.aliexpress.com/i/1005006357940015.html

Lucid DAC disconnected, Resistance from DAC chassis to both RCA shields gives good continuity. Power on & music playing, Readings from power ground to both RCA shields, both DC & AC =0 volts.

Rodders53 The source is my Hisense 43E7KQTUK TV The material could be anything. I also Bluetooth Youtube Music from an Android tablet. Lucid I will get back to you with the results of your test at some point.

Lucid Yes I do have a multimeter, but I don't see how that will help me. Fred Blogs Your link to the Prozor DAC looks exactly like the one I have. The DAC that I am now using is a replacement for another one which had exactly the same problem. I bought the DAC to bring my HiFi up to date but...

Output from my D.A.C (Prozor 192kHz) to my HiFi (Technics SA-EX120 AV) is low, meaning I have to turn the volume on the HiFi up very high to get any decent sound from the HiFi. This happens using Either optical or Bluetooth input to the D.A.C and the volume on the D.A.C at full volume. Would it...

Thanks for your help.

I was unable to be connected to full fibre about a week ago, but Open Reach left me the O.N.T, (which we agreed on its location). The fibre cable has not yet been installed. I want to install the O.N.T to save time when hopefully they return, (it's only 2 screws). My question is how close to the...

Thanks for your help. I guess the light circuit was changed over to the R.C.D to comply with regulations?

I had a garage conversion done a few years ago and I have now noticed that the sockets on this circuit appear to be covered by a 16 Amp circuit breaker. Is this a radial circuit and if so, is there a limit to how many sockets can be connected to it?

D-line mini trunking does not come in 25mm x 16mm & it has Pvc Mini Trunking Accessories for corners ETC. D-line recommend 30mm x 15mm for 2 x 2.5mm T & E, I only need to run one cable?

Is it OK to use 16mm x 8mm D-line trunking for a mains single (spur) 2.5mm square T & E cable, the cable is O.D 10.3mm x 6mm? If so what surface mount double socket box would you suggest?

Thank you all for clearing that up for me, I will get on with the job now.

Thanks EFLImpudence I notice that under (Do I need to inform anyone?) you answer NO. I have found this thread https://www.mybuilder.com/questions/v/11251/spur-a-new-twin-socket-from-existing-socket which says otherwise. I don't know who to believe.

Could I use something like this to test the circuit before and after...

Am I as a D.I.Y person allowed to connect a spur for one extra double socket to an existing ring main socket in a bedroom? Are there any tests, like measure loop impedance or certificates required for this? Can this be done without the need of a qualified electrician? Do I need to inform anyone?