Search results

Many thanks Terrrywookfit

Hello everybody. Is a Danfoss BFP 21 L3 pump a suitable replacement for a Danfoss BFP 11 L3 ? Information would be gratefully received

Many thanks for your advice Bob - much appreciated

On startup, the burner would fire for a period of app. 10 second, and then cut out. It would attempt to restart and eventually cut out again. After about 3 resets, the burner would finally stabilise. The problem worsened. Finally, after resetting would again, there seemed to be a sudden...

Good Evening, I wish to replace the oil filter on my central heating system. Could someone advise me if a 10mm copper pipe can be directly connected to the oil filter, or will I need another connector? Will I be able to connect the oil filter directly to the fire valve using 10mm copper pipe...

Thanks John

Finally I found the problem with my integrated dishwasher. We purchased a new kitchen about ten years ago and paid quite a sum to have it professionally installed. Returning to my problem, I reluctantly removed the integrated dishwasher with some difficulty, since I had no idea how it was...

Good Morning My house is fitted with imperial measurement piping. Only metric is now available My Question ======== Can I use a 10mm straight through connector to connect 3/8 inch pipe to 10mm Can I use a 10mm straight through solder connector to solder a 3/8 inch pipe to a 10mm Can I use a...

Thanks again John, You wrote " I cant see the drum pulley coming off with the screw still in place, unfortunately." I think that you have mistaken what I was asking in my question. As you know, to change the bearings I have to remove the drum in one piece from the machine. The two halves of...

Picture of screw that I am trying to remove. As regards the red threads on the bottom, they appear to be some type of a sealant such as loctite. I am a bit worried about using heat as this could damage rubber of plastic components in the vicinity..Has anybody experience tying to drill through...

Thanks again John. Taps are fed direct from the main. Stop cock is fully open. Washing machine is OK. Some months ago, the Water Authority fitted water consumption measuring machines. Since then, the water pressure seems to be particularly low. Perhaps, it would be a good idea to get the Water...

Many thanks John. However, when I switch on the cold water tap in the Kitchen, the pressure indication on the pressure gauge approaches zero. Same thing happens when the washing machine starts to fill. Any ideas? Many thanks, Jiommy

Good Morning. An Error Code is appearing indicating that the machine is not filling up within a set period. I have checked the mains water pressure. Meter reading is: 20 PSI (1.5 Bar) Is this water pressure adequate to enable the machine run properly? Any advice would be gratefully...

To: rsgaz, assuhors, Burnerman Many thanks gentlemen for your replies and advice. I have ordered a replacement bolt for the machine to check that it is not a left hand threaded bolt.

I am trying to replace the drum bearings - Have full instructions I have run into the a problem- I am trying to remove the pulley wheel from the Drun spindle. It is fastened with a countersunk hex headed M10 x 25 bolt. I cannot get the bolt to budge. I inserted an alan key into the hex head -...

Many thanks Handymanjoe for your suggestion. However, since posting this question, I have located the NEXUS 8, Alarm Panel Guide. This guide gives details of how to access and adjust the Master Unit Menu. I have succeeded in changing the Master Unit Code.

Good evening all, I have reset a Nexus 8 Alarm Panel which I installed myself. I have the Engineer Guide for the Panel and I have reprogrammed the unit. However, I have run into difficulty when trying to change the Master User Code. I have succeeded in changing the Engineer code from the...

Many thanks big-all. Could you recommend a good blade?

Good Evening. I have a Black and Decker Jigsaw. I fitted a brand new blade. I then used it to cut through two 4ft. lengths of 18mm chipboard. The blade was then totally worn out. Is this normal wear. The blade was a C.K type C. Any advice would be much appreciated

Hello Sparkymarka, Thanks for your help. I fitted an old keypad which I had for a long time. I then found that a PF message appeared. There had been a mains supply failure a few days ago. The Power Supply in the unit had a blown fuse and s/c capacitor and faulty rectifier. I repaired the unit...