Search results

OK Thanks every body,Its not my property so im not bothered just doing as asked. Sounds lika a wet system is the way forward.

Hi, would like to know about underfloor heating . The project were on has a concrete floor with 50mm insulation and chip board on top ....Can i put underfloor heating on top of this chip board and then cover with solid oak flooring thanks. Ps what wattage does this run on Martin

Hi again could somone please give me an idiots guide to rcd testing on a light ctc . I can only assume that with skt outlets the plug on my megger unstables the current do to causing an eatrh leakage ,Do you use the three probe leads on a light and what is the process of two or three way switching.

ok and yes i am capable of doin live test ,im in early stages of training. is it right to have the light switches in the open position .....what about two oo three way????

Hi can someone please explain how to Zs test a light circuit. do you have to do it at the light fittings only and what is the procedure of the switches on the fittings and the c/unit many thanks to all , I have a megger 1502 with three lead output

Hi can i ask what all you think of crimps to extend wires are they allowed as they dont seem that secure to me,Can you tell me what colours to use with 1.5 and 2.5 t+e .What is the biggest wire you can crimp????

Hi cheers for that ,I changed the fuel filter yesterday and found some very small dirt particles i can only assume that came from the bottom of the tank as it was low when i bought it. So a new filter and ring seal seems to have done the job with a full tank of clean derv,no fillings so im happy...

Hi i have recently purchased a 53 plate expert 2.0 hdi, I have had no probs up until now .The van was running fine and then suddenly died being quite mechanicaly minded ive narrowed this down to a fuel problem,Ok so driving a while, it died at a junction ( VERY PI"£$ED OFF) Waited a while and...

yeah >299 dur ! it was the 500v ir test i done sorry had a blonde moment, yes the house has 3 ring mains all in 2.5 t+e these three are the only ones on the rcd . so ill ir all three rings tommorro and get back to you . any other suggestions to find a fault I heard that there was no such thing...

Hi just to let you know it was a crossed live Hey Presto LIGHTS :shock: :D :roll: :wink:

thanks i have a calibrated megger 1502 and have done an ir test through the r1 ring but never thought of the rn i have recently got my part p certificate i know its not a proper qualification and in any way not a qualified spark so im still learning so any help will be gratefully recieved.The...

Hi , I have a friend that is having a problem with her rcd tripping at least 6 times a day,and over night.She has quite a big house and recently a new small extension,In this extension she had an extended ring to supply a dish washer ,tumble and washer.These were in the kitchen before but on...

Thanks ill let you know the out come if i get one !!!!!!!!!!!!!

Cheers mate by the look of it someone has messed with this aparently you couldnt switch on the lights in the kitchen unless one of the three way switches was on in the hall so im guessing this has something to do with it

My sister in laws is having problems with her kitchen lights, so ive had a look and put a mft on it and found that there was 244v from live to earth but only between 130 and 188 v from live to neutral. i also noticed that the said lights are connect some how to the hall lights ive tested back...

Was told last night that it would work out better to just demolish the garage then dig for the foundations , any one got any comments on this he is a very good friend of mine. and a time served builder..the under pinning will take longer as i will have to hand dig it by the meter and try to get...

63.27 + vat the cheaky fookers

Hi my in laws bought a 04 reg mondeo 2 yrs ago ,2months ago it went it limp mode and the diog said it was the map sensor .never bothered to replace it and all of a sudden the turbo juddered and started working again. could this of been the accuator sticking in the turbo itself ,as i believe...

Cheeky biatch........

ok will speak to my local bc spark before i start this job