Search results

thanks zipper you are a starrrrrrr regards barry

Hi all could anybody help me on how do i change the drum bearing on a Hotpoint WMA 31 washing machine sounds like a fighter plane coming into land any help would be appreciated regards barry i am a very good diyer so plenty of tools ect

hi all i have recently got the caravan out of winter storage and found that the the fridge is not going cold on 240 volt but works fine on gas any help whould be appreciated bazzzzzz

can any one help me to identify the fault on my turbo diesel vectra 07 aircon when i switch the aircon on the compressor is not engaging on the clutch i checked the feed to the clutch and their is no power to it so it wont energise the clutch and i checked the relevant fuse but still no power...

hi all can anyone suply me with a scematic diagram of a zafira gearbox 2ooo reg 1.6 petrol it sounds like the differential bearings are on the way out but the heynes manual does not give a breakdown of the gearbox having done numourus anounts of back axle over the years wish to do the gob...

i have a renault scenic 04 plate and the front door window went down but not back up i can hear a noise but nothink is working how do i get at the unit to see what has happened is it a cable or mecanical arms hope it can be sorted be you clever guys thanks barry

Hi all i have recently bought a vectra estate 07 and it has 19 inch alloy wheels on and i noticed that it has a 13 inch spare. its one of those emergency spares but surely it is ilegal to put a 13 inch wheel on with a 19 inch can anyone tell me what size spare wheel it should be if it was to be...

Thanks to you all for your help i guese i will have to see the wife for more pocket money and buy some good tapps regards bas

the taps are about 18 months old they are bathroom sink taps both hot and cold are tight also the utility room taps are the same also tight to turn on and off they were bought from B+Q thanks bas if i grease them they last about a month then go tight again

hi everybody i have a problem with all the taps in my house they all go tight after a couple of months is their anythink i can do to cure it or is it down to the cheap taps being sold now days any help please i have greased them but it does not last long is thier a special grease for them thanks...

yes if you take the cover off and use a peice of alarm wire to link the PA out that will be fine just turn the power off and leave the battery conected, if the alarm goes off you should be able to reset it when you fit the wire link fit the cover back and oress reset good luck bazzzzzz

if you turn the mains power off to the alarm and take the control panel cover off and disconect the battery, waite a few seconds and conect the battery back up and put your number in all should be reset, now press reset and put the cover back on and turn the mains on hopefully all will be ok

author have you got a personal attack wired up in the house, if you have i suggest you put a link wire in the control panel on the PA terminals and see if that cures the problem, if it is a PA or TAMPER fault then the key pad should become unresponsive and locked out or does it clear when you...

yes ""what you will have to do then is get hold of a new battery from a local electrical wholesaler it is probably the origanal so it needs changing any way, GET A 2.1 OR A 2.6 AMP HR so if you get a new battery then you can press PROG 9999 and open the control panel up and change the battery...

tsp do you have the engineers code for the alarm If not try pressing PROG 9999 and see if the tamper light is lit or the attack light is lit,if one of these lights are lit then you can open the control panel up after you turn the mains power off, If neither of them light up then you will have...

fatpieman why are you messing about trying to mix and match how much did you pay for the keypad lcd because you can buy a complete set up for around £43 00,key pad and panel, i priced a lcd key pad and it was £29 00 + vat so a complete system would be cheeper, and the answer to the question will...

did you fit a link wire to the PA and set to reset the alarm if you did then you will need to put the link wire back in the PA AND PRESS THE RESET

Hi cruisa I have been in touch with technical support and they said if he has a permanent negative supply coming out of the control panel to the bell box strobe then the panel is faulty. hope this helps. ask who ever supplied the control panel to just replace the print board as this will be...

HI cruisa sorry to hear you have still got a problem before you send the unit back try the technical help line the number is 0844 8000 235 IT MIGHT BE SORTED BY THEM can honestly say i have never had to send one back or get advice on any of gen range only in 35 years had to take 2 pir s back...

cruisa did you say that the green day light is on or off on the keypad because if it is on i suspect you have a faulty panel have you tried defaulting the panel to factory set incase you have got a glitch on the eprom worth a try before you send it back to do this remove the mains supply and...