Search results

Rocks. What is type of thermostat for this fridge. It has no ice box. I have seen both Ranco K59 H2800 and Ranco K59 H1300 fitted to this type of fridge. Thanks.

I agree. I wish the fridge i have would have such fine control! Appreciate it.

Clearly the solenoid should activate or do something when it is powered up and the action of the door being closed is simulated.It is impossible to tell just by looking at it if something is wrong unless there is clearly a broken or burnt part. I couldn't see anything wrong with the one I was...

Stuaert. I don't think cleaning out the pressure switch tubing will do the trick.

Steuart. My sister in law had a similar model and it broke down a couple of years ago. Alas I cannot recall now exactly what the symptoms were other than it wouldn't do anything. I cannot recall if it threw up a fault code or not! However I think that it was not totally dead as there were...

I would suspect the door interlock is faulty. They cost about £20 and are readily available on ebay and other "spares" sites. Easy to replace. Switch off machine at mains. Pull back rubber door seal (proably need to remove door seal ring) at lock side. Remove screws holding linterock in place...

When machine was working normally did door light stay on? If you try and do a wash now does light stay on or not.

Does the light come on at the door. Frequently the interlock gives up on these machines! Sometimes slamming the door does the trick but not too hard please

Rocks I bow to your experience. However even when I defrost the fridge and clear off the build up of ice and turn it back on again the fridge temperature doesn't drop below 10 degrees approx even though the compressor never stops once. The compressor churns away but the temperature remains...

Thanks Rocks. can't understand if thermosat is faulty why temperature doesn't get any lower and auto defrost ain't working.

My Hotpoint Integrated fridge(Model 6935) of some 17 years vintage stedfastly refuses to drop below 10 degres centigrade. The compressor never stops presumably because it doesn't get cool enough - it doesn't switch off no matter where the control is turned to except when the control knob turns...

You should know if it spins the clothes after washing them! Assuming it has spun them as dry as it possibly can for a spin then if it is not drying them it is likely that the cold water feed to the dryer is not working. This is one part of a three valve arrangement part that allows water into...

Are we talking about little green thingy for siphoning out the fabric conditioner? A trip to the local council tip should procure one.

Malatron. Your hot water is never free. I know it seems a shame to waste the water from your Aga. However even with lagged pipes there is frequently waste of "hot water" before it reaches the washing machine. With washing machines using cooler and cooler washes it appears simpler and more...

Chrisjs -Glad you got it apart. Unfortunately I did this repair to my sister in laws machine a few months back so I can't readily refer to it. I had no problem removing valve together with extension piece from plastic D insert on rear panel. My problem was unscrewing valve from this extension...

Release wiring from 3 sockets, unclip hoses from valve. Alas I can't remember exactly how to undo end at rear panel other than indicated in the reply of 12 December. The valve will be released but together with a small extension piece joining it to plastic insert in rear panel. Once you have...

See my entry dated 12/13 December 2008 on changing valve.

Can anyone suggest where I could get a thermocouple and Front Coal for the above gas fire please. What about a universal thermocouple. Alas this fire is some 16 years old.

Thanks to previous posts I was able to replace triple water valve on this machine. Symptom was displayed E10 code and failure of dryer to work due to open circuit solenoid on one part of water valve that allows water to flow to condensor. Got slightly stuck trying to remove small piece fitted...

What is problem with this machine? There are numerous posts on this machine in the forum.The answer may have been already posted or someone else may suggest an answer.