Search results

Thanks secure, added the second bell and extra zones no problem. Method i used was to learn the sounder and then send over the panel data into wintex. I then added the 2 extra wired zones to the program and sent back, all working great. One further question if i may, i installed this system as...

Hi. I have a Prem elite 64w panel. I wish to add a couple of hard wired zones and a second wireless sounder. I have modified the program on wintex to account for the new hard wired zones. What is the best sequence which to do all this as i had a few issues last time with the richocet and mesh...

Will be taking delivery of a Dunster House log cabin shortly and was wondering what the best reasonably priced treatment/stain was? It is spruce wood and quite light looking. I would like to treat it for protection against the elements but maintain the same or similar colour. Anyone any...

Much much prefer wired myself and did this wired where possible but with it being one of these modern chipboard houses, some of the runs were not worth the pain. This was my first Texecom wireless and tbh, ive been impressed with its performance thus far. Will play safe and change batteries...

Thanks secure, i am going to go wireless as i have plenty of spare zones available, cant wait to have another go at doing the mesh again........it seemed way more complicated than programming a wired panel last time i did it. As a side note, how often should i be replacing the batteries in the...

My concern from what i have read on other sites is just that yes, water running onto and under the base and rotting the bearers. I will be fitting a guttering to take the water away from the roof and even though the bearers are pressure treated, i will add a coating or two of preservative...

Installed a 64W panel last year. Used a combination of wired zones and some wireless. Am pretty impressed with it so far and have no issues although i wasnt a fan of the richochet learn part. The Sounder is wireless. I am wanting to add a second sounder to the rear of the property likely also...

Advice on the best course of action would be appreciatted. I have had a concrete slab installed in my garden onto which i will be instaling a log cabin. Hardcore subbase, visquine sheet and then 5'' of concrete in the shuttering. The concrete level sits an inch above the lawn. The cabin will...

Hi Not something i have ever done so would apreciate some comments from the experienced. I have a 4mx3m Log cabin to install in my garden so obviously my first job is to build a base. I will be doing this myself as i am more than happy i can do it and am very practical. The cabin is from...

No, i didnt know there was a drain cycle tbh...... The machine doesnt seem to drain, i have to empty the water manually when i get the fault code and at the time the fault code happens its when i presume the cycle is ready to dump water ready for a refill/top up (if this is how they work)...

Can anyone give me pointers as to what to fault find regarding this error code. Machine has been in storage in a house for about 7 years and was used only half dozen times before that. Taken out of storage and tried three times now to do a quick 30 minute cycle and it gets halfway through...

So just open the panel up and move the jumper over and silence the tamper? (in eng mode or normal?) My devices all being yellow for signal strength - is there any way to improve this? Thanks

Its a live 64w so expander built in........so simply putting in eng mode and moving the jumper will start commisioning? Do i have to be in Wintex diagnostics when i do this? I never seemed to get any indication i was in commisioning mode or when it had finished? A step by step would be really...

Following on from this I installed panel, learnt the devices, recieved data to wintex, programmed and saved, sent data back to panel. The bellbox, PIR's, contacts all appear to work including the one wired zone. The only issue i seemed to have was with with the commisioning mode and ricochet...

Thanks for the info Secure, just signed up to the texecom forum. Would be good if i could play with it all before install so i could set up at home beforehand. Is there a way of doing this? i.e stick 240v onto the panel from a lead and program and learn all devices? Would the panel not 'forget'...

I can imagine that is a bit frustrating!! How do i get to the commisioning mode and at what point do i do that? Also, would i be right in thinking i can learn all device (including sounder) and then fix them all in locations after?

Thanks secure I will do the first as it seems most logical. so to confirm 1, install and power main panel with my one hard wired zone 2, learn all the devices on. 3, connect USB/Com and recieve 4, program 5, send back and save What is commisioning mode? Ive never used that, only ever used...

Thankyou, thought that was the case. Regarding programming and learning..... I will be using one hard wired contact on the panel and 4 wireless devices. Is the process to learn all the devices to the panel and send my program over via the usb/com AFTER they are learned? If so i take it i just...

Hi guys Got a Prem elite 64 -w live panel to install at the weekend and am just doing the programming on wintex so i can send it straight over. I have updated to wintex 7.0 yet. When i go to select panel type i dont have the 64w-live in the drop down box. I take it i just select the elite 64...

ok cheers, hopefully he will look at the thread at some point.