Search results

Looking to order in some UFH heating pipes to be installed over a concrete slab and a block and beam floor. Once pipes are laid will add 70mm of screed. Is there any particular brand to go for? avoid? any deals? Thank you.

Any one kindly offer advice? Option 4 62.5mm Insulated plasterboard straight on to the walls using foam (50mm insulation/12.5mm plaster board). Issue with this is that i don't think the walls will be strong enough to hold any fixtures and fittings. As mentioned before, i do not want to...

I am planning to insulate my basement using metal stud - which will be a floor to ceiling attachment. Reason for not going down traditional wall battens is due to not want to compromise the tanking slurry applied to the walls. I have just seen this stud in Selco >...

With the metal studwork would it be best practise to have foiled back insulation board right up against the tanked walls, or should a gap be left? Am I correct in thinking that metal stud walls are designed to have plasterboard directly attached? unlike a battened wall where you would install...

What about using glue to fix batons on to the tanked walls?

Was just watching a video on youtube about this. Appears to be simple method however do the insulated plaster boards come with a vapour barrier? As it is a tanked basement there will be condensation, therefore a vapour barrier of some sorts will be required. Thoughts? Just read that the...

Semi Basement constructed from 325mm concrete blocks and infilled with C35 concrete and rebar. Walls have been tanked using KA Tanking Slurry. The floor has 100mm rigid insulation and a concrete slab. Wet UFH heating will be installed. Next step is to add in some insulation. Which would be...

Did you go down the route of installing the ventilator? I am doing something similar so would be good to have your thoughts on if it was worthwhile. Many thanks.

Thanks for reply. I spoke to the manufacturer of KA and after our discussion decided that SBR is not needed on the walls as they were fresh concrete blocks. I will however use SBR when using KA on the poured concrete slab floor.

Bosch Classixx Vario Perfect - WAE28166GB The machine tripped the RCD whilst running a cycle. Since then it will not start any programs. When pressing start the buttons light turns solid (as it should) but the machine does nothing else. At this point it should start drawing water in. No...

Planning to use tanking slurry on a building this week. Walls made of up freshly laid concrete blocks. Products: KA Tanking Slurry KA SBR Has any one had experience with KA products? I was planning to coat the walls with KA SBR at 1:1 ratio, then paint on slurry, wait till dry and add...

Beam is supporting a new pitched/vaulted roof/ceiling. Extension to the rear of a bungalow. One side the beam sits on a internal cavity wall. The other side sits on a internal wall. On top of the beam Aris rail have been installed and roof tiles on top.

Part of a build I have been working on this past 12 months. Rear extension of a bungalow. Pitched roof Vaulted ceiling 9x2 rafters Breathable roof membrane Steel size is 9m @ 203x203x46kg and is sitting on the inner leaf of the walls. Windows/doors/bifold were installed just under a week ago...

Thanks both.

I shall be getting my property rendered in the next few months. Heard stories of K Rend going green so not too sure on that? Weber - Monocouch - was thinking of going down this route. I had some one over earlier who users PRB. Has anyone had any experience with this render? Many thanks

Extending to the rear of my bungalow. Black square is existing building Red is new building which is to be attached to black existing building. The cavity around the existing black building is approx 70mm - which is NOT filled/insulated in anyway. The cavity around the new red building is...

Can any one advise what the general rule is building a double storey side extension next to a highway (corner plot property). How far from the highway does the build have to be? Does this increase if it is a double storey? I already have a single storey built, thinking of adding a double...

Update: The fan had packed in and has now been replaced by an engineer. All working. Thanks.

Loss of hot water and central heating. The circled icons are new to me... ive had a look at the manual and i cant figure out what they refer to. After they flash for approx 30 secs the F33 code appears: f 33 Main heat exchanger anti freeze protection mode Check air pressure switch, fan, fan...

Thanks. HiKvision name always pops up… I will look into synology further.