Search results

I want to buy a single Lever monobloc kitchen tap, but I need it to have the Lever at the front like the one below. Can you literally buy any other tap like this that has the controls to the side and turn the tap so the controls face the front, or do you have to buy one that specifically looks...

Funnily enough I saw that a bit earlier will give that a go

Any ideas chaps? when I say hinges I mean the plastic sliding clips they give you to attach to the door and fridge freezer door.

I'm fitting a kitchen at the moment and it's pretty much done, but just having trouble with the integrated fridge/freezer door! The door is level and fits to the carcass fine. But when the hinges for the fridge door are attached the door doesn't close in the same position (it's hinged on the...

It's a blanco sublime 1.5 bowl granite if that helps, is there a waste connection that takes up minimal height for two bowls and a dishwasher?

Really good point about the supplies. Unfortunately they are already in and protruding through the top of the unit! Do you think it's worth removing the sink unit and lowering the hot and cold to come in through the bottom

Trouble is I need the sink in situ don't I? The sink is undermount, so I can really Plumb the waste in until that's in or would you start from the stack run the waste at a 1:40 incline towards sink by chasing out blockwork then its there for when you need to connect

Many thanks gents, much appreciated. Would you say I am ok to get our Quartz worktops fitted and the plumbing side of things shouldn't be too much of an issue as I can still pull the dishwasher out.

So cut the hole in the boss, then the insert goes in the stack, then the the pipe goes in the insert?

OK so use a hole saw of a the same size to cut then insert pipe? I think by the time I have fitted waste to underneath of sink I will be too low for the higher strap boss connection already in place, would you agree? (under mount sink 190mm depth) The top of the stack is fitted with a push fit...

Ok, the bottom circular area on the soil stack, is that a premade connection point that needs to be drilled out?

It's a CGI pic above shows how it is now. Easy enough to chase out, it's just block. Never really worked on drainage before though 1:40 fall? There is a new exit on the bottom of the stack will that be ok to use or should I use the one at the top which was used previously (the one with the pipe...

Yes it should have been I did ask my plumber to do this but at the time we were still using the stack for sink waste up until the day before the new kitchen arrived and hard to get him back before we started work. The dishwasher is integrated to the right of the sink. The above pic is just a...

Hi, I'm fitting this kitchen at the moment, I'm pretty much done but I have to figure out a way of running the dishwasher waste and sink waste to the soil stack. The stack sits at the back left corner of the pantry cupboard. There isn't enough room at the back of the dishwasher to run a waste...

Is it possible to get a pump on the hot feeds? I already have a dedicated pump for the shower upstairs I presume I cant run it off this as pumps both hot and cold to the shower, so I would need a single feed pump in the airing cupboard on top of this?

I have a tap downstairs in the toilet which is a mono basin mixer. The cold is fine, the hot dribbles out, presumably this is the issue you are referring to?

Right ok, so general consensus is 0.5 bar should be ok. Just need to get this right as they are going to cut out tap hole for quartz worksurface so need to make sure it's going to work. Guess I could always connect it up to the supplies on flexis and run it into a bowl to check.

Hi, I'm having my kitchen replaced and I need a new tap. Cold water comes from mains with very good pressure. Hot comes from an vented hot water cylinder so pressure not so good. I understand I need a low pressure kitchen tap. I've found one that works at 0.5 bar min, in general would this...

Many thanks, will have to take a look once our kitchen project is finished!

It did! However the draincock was one where you had to put a bleed key in to release the jumper the attach a hose!