Search results

My washer dryer has started showing F13 again. I replaced the element a couple of weeks ago (it was open circuit). There is no fluff in the heater box and the fan motor is working fine. One thing i have noticed. Should the water valve be running constantly when the dryer is on. I took the...

Hi there My mums integrated Indesit IWME12 washing machine is playing up. No matter what programme you select the timer says it will take 4 hours. Could it be the PCB?

Need some advice please. I have a Hotpoint BWD129 that is taking ages to wash. All that happens is the drum fills with water and then it just washes and washes. No rinse, no emptying and no spinning. I put it on a 90 degree wash this morning and after 30 minutes i drained the water and it...

I've just recently had my kitchen wall replastered after a massive leak from the bathroom. The bathroom has all been sorted out. Its now two months since the kitchen was replastered, and i've noticed all I can describe as wet patches that appear to have salt coming through. Does this make...

Hi there My friend had the same problem. His Zanussi had an anti flood device that had gone dicky.

Had a new Ferolli condensing combi boiler fitted in February to replace my old combi boiler. After it was fitted the thermostat wouldn't work. The guy who fitted it put in a new thermostat, but that will still not work. And is now not answering the phone!!! I've had a gas man look at it and...

There is no water going into my condenser dryer draw. When you first turn the dryer on water pumps out for about 30 seconds, then no more? I tried pouring a cup of water into the resevoir where it's pumped from and that worked fine.

Hi there I have a Hotpoint washing machine FEW 10 that is 3 years old. The door locked light keeps flashing and now the active light is flashing aswell. The machine will not do anything. Any ideas please?

OK i've changed the brushes. But it hasn't made any difference. It will still only spin with a half load. I've checked the pump and thats fine. Starting to think there is either a fault with the motor or main board. Any help would be more than welcome.

I have a Siemens washer dryer that will not spin with a full load. If I take out half of the clothes, it spins fine. I have checked the filter and thats clear. Any ideas would be very welcome.

Hi there I just need some advice please. The dryer has stopped blowing hot air for the third time in 3 weeks. Every time the button just needs pressing on the thermostat to fix the problem. To rectify this problem, do i just replace the thermostat with the reset button? Or do i need...

Hi there After the pump runs for a few minutes the machine beeps, and lights 2 & 3 start flashing. Nothing else happens. No water goes into the machine. Anybody any ideas???

Thats great, thankyou Rocks1. Do you just mean the oven door is not shutting properly?

Hi there Does anyone know what Error code E8 is on a Creda Oven. The oven works for about 30 minutes before the error flashes up. Thank you

Hi there I've got a Hotpoint WMA44. When you shut the door and press start the door locked light starts to flash and the machine does nothing. My father tried changing the door interlock, but it made no difference. Can anybody help please???

How hard is it to reverse the door on a tumble dryer. The model i have looks to have a proper door interlock. It says the door can be reversed. It has all the holes to be able to swap the door. But how do i change the interlock? Is it just a case of taking the top off and moving it to...

The fan wheel on my Whirlpool AWZ3303 tumble dryer has split and needs replacing. I ordered a new fan wheel from UK Whitegoods. The problem i now have is that the new wheel will not fit onto the motor. It is the correct replacement, i just presumed it had been modified. The motor has two...

Hi there Problem with a Hotpoint WF541. All the lights are flashing continuously. When you first turn the machine on from the mains, you can start your programme, and it will go through the cycle. The lights start flashing almost straight away and you can only stop them if you turn it...

My friend has a 15 year old Hotpoint 800 Electronic 9506. He said it was taking ages to fill on a rinse. The hot water comes in really quickly, but the cold just trickles in. Ive checked the water valve filters and they're clear. Does it sound like the cold water valve needs replacing?

Hi there Lights 1 & 3 are flahing. I have read previous posts about the Hotpoint error codes. Lights 1 & 3 = Pressure switch not sensing. Can anyone give me a few more clues as to what the problem could be. Thank you.