Search results

Thanks again. Apologies if I have misunderstood but as I have a wago junction box spare and a load of T&E, cant I just put the exisiting cables into the wago 221 box then put this into the wall(Cable tie it!). i can then run a new bit of T&E and come out inside the back of the mirror and then...

In the In the photo if look just where the cable is there is a small line above it, this is the top of the mirror. So they will be just below the top of the mirror. Thanks again.

Ok, so you want me to remove the flex from the mirror and put in a longer one? Fit a standard back box in the wall? Do you mean a flex outlet rather than a blank plate, otherwise where would the flex go? Sorry just seemed quite lot for a cable coming out the wall? Can I just put the Wago box...

Ok, so you want me to remove the flex from the mirror and put in a longer one? Fit a standard back box in the wall? Do you mean a flex outlet rather than a blank plate, otherwise where would the flex go? Sorry just seemed quite lot for a cable coming out the wall? Can I just put the Wago...

Thanks but what do you mean the connections have to be enclosed in a box, isn’t that the second option? The flex from the mirror is typically at the bottom and it just about reaches to the top so won’t fit into a box in the wall. Do the Wago have to be in a box even if they are accessible? Many...

Hi Just after peoples opinions/advice on the following. What’s the best/preferred way to wire a bathroom mirror in, see attached photo. Connect off wiring as per photo using a 3 terminal Wago and connect the mirror flex to this. Or Put into a Wago 221 Wago box and then leave this in the...

Cheers

Hi All, I have brought some 221 Wagos, the new lever type. There are 2, 3 and 5 terminal connectors as per photo. I have looked and they don’t seem to do 4 terminal connector. My question is, I have a light fitting that has 4 permanent lives do I just use the 5 terminal connector and leave...

Hi, Just after some advice, I have a extractor fan, bathroom mirror and some lights to install. What’s best/preferred 1mm or 1.5mm? Many thanks

Anyone installed/have a croydex mirror, are they any good,thanks.

Cheers, seen this. Anything I should be mindful/wary of? Any one is installed one of these or any other croydex mirrors...

So if you were me you would just charge them somewhere else? Is it Worth getting a mains mirror with light as I have a cable already in the wall? What are the battery ones like? Cheers

The socket on the mirror would be for toothbrushes which are currently charged elsewhere. Would you just continue to do this or buy the mirror with the built in socket. Thanks again

Ok thanks, how about toothbrushes do the same? Just charge them somewhere safer? As I have the cable there should I just go for a standard mirror with a light? Thanks all

Hi What are peoples opinions on bathroom mirrors with built in shaver sockets? They seem pretty expensive, would you go for just a normal mirror and a separate shaver socket? Or are the built in ones better? Many thanks

Had to do it that way as wanted NMP on the bit towards the wall as it’s only 6mm instead of 12 for the aquapanel, have a extractor at the top of the wall so didn’t want to block it. NMP is a pain to cut as well compared to aqualpanel. Almost done now with the trim, thanks anyway though. Thanks

Sorry what do you mean, a big timber gap? Thanks

This is the trim I am using https://www.toppstiles.co.uk/fixing-finishing/trims/topps-tiles-10mm-stainless-steel-effect-square-edge-trim#selection.trim_product_colour=Silver&selection.trim_depth=10mm

Hi Just after a bit of advice with tile trim, have an external corner to do as per the attached photo How is it normally done/ preferred way of doing to? bed all the trim onto the wall first, making sure it’s level and leaving it overhanging a bit to allow for the other tile going in the...

Just wondered if anyone had any ideas? Thanks