Search results

Woooooo there Taylor me lad! OK, there will be loss along the way that's ivevitable, the same is said for the 5 velux windows that are in the vaulted ceiling and the 4 meter bi folding door at the back of the extension that will not help in keeping in the warmth even with the rated glass in...

Afternoon all, Need some guidance (comments/likes/dis likes/web links etc) on buying new led spots for my kitchen/diner/living room. I want to stage it in three areas 1) Living area (8 Led dimmables) Dinning area (6 Led non dimmable) Kitchen area (8 Led non dimmable). In the dinning area...

Agile, boiler being moved tomorrow with original flue being used as have better wall clearence further down the kitchen extension, i will post a pic though when its done. Mickyg, new cheap one coming up in new year, hope it lasts as long as this cheap one did :wink: I am actually saving...

Yeah the guy moving the boiler is gas safe, well he has the card for it. I cancelled the similar parts and came up with an easier solution as to moving it to the small utility room an not the garage, the wall that the flue will now stick out will be fine for a vertical flue! I will be replacing...

Riiiiight, you cant run a HE flue on an SE boiler, BUGGER! I ordered a flue, which i thought was the correct one, but looking at it after your reply it wont work! It arrives tomorrow and was going to see if the vertical flue adapter would fit and if it did then bingo! But i think the parts will...

Hi Guys, Anyone know where i can get hold of vertical flue parts for this boiler? It's been working brilliantly since my last helping hand (cheers all who helped) and now it is being moved in to a garage extension this week and i need to change the horizontal flue to a vertical flue and...

Yes.

Hi, My Heatline C28 fires up on CH for 60 seconds then shuts off for a bit then fires up again for 60 seconds then goes off. This is when the CH is on for a while and it has been doing this for some time. When the boiler fires up the temp indicator goes up from 60 > 70 > 80 then the boiler...

Before i start, again, i would like to say a big thanks to all who have given me some great advice! Cheers lads! So.... Well after a few months the boiler limped along with nice CH and hot water, then HW reverted back to hot to tepid again 30 secs hot 30 secs tepid. So i finally got around...

RIGHT!!! Got you now! Sorry for being think as! Well it looks like the HE is getting a good looking at this weekend then! Pete

Well when the boiler switched off and was blinking on the 80 led i pulled off the limit stat and re-seated it and it came back on. After setting the blue switch in the DVM correctly meant the DVM will now switch between CH and DHW and now both CH and DHW are working like new. I will see...

Got in touch with a mate who's a fitter and he worked out that the DVM wasn't working correctly so took it to bits and noticed that one of the switches wasn't correctly sitting (the blue one in the pic), reset it and silicon greased the bits and clicked it all down and checked and now when the...

DV kit arrived and gland and pin replaced, all gunged up!! Dropped all pressure in system and re did the EXV, hot water and heating now on! The pressure is not rising, as think the EXV is pumped but now the temp goes up to 80 and then the boiler switches itself off. I think i missed...

Tony: Sorry m8 im putting too much info in and confusing people i think. EXV: I couldn't re-pressurize the EXV as didn't have anything to hand to do it with last night, but i will have tonight as one of the lads in work has a pump and a digi pressure gauge! I read that i need to drop...

Update: I set the DVM so the pin was open and then plugged the cable back in to it and then put the elec back on the boiler and the motor does work because the pin moves back in to the flush position as shown in the second pic. But when i put the DVM in to the DV put the clip back in and...

Fond the expansion vessel at the back of the boiler and took the screw cap off and just pressed the valve a little bit to see if anything came out an there was nothing at all. So the vessel needs to be pumped back up but ive got nothing that i can put on it! So a bit buggered there! Just...

DVM and DV in case this helps? Im not sure if the DVM wheel and pin is set in the correct position or if the switches are OK either. I have not touched the switches and only moved the wheel to move the shuttle type pin backwards. The DV has been cleaned out this was taken beforehand. The...