Search results

Thank you for the advice John. I booked it with Vokera fix repair, service and one year warranty at £251.94. Engineer was near, he popped around yesterday afternoon. You are spot on John! Engineer find Condensing Unit faulty (345+vaT= £414.00) He reckons, also 2 other parts needs...

Hi, My 5 year old Sabre HE 25 combi is leaking water. I have attached the picture. Not pouring out, but it is leaking. Pressure drops from 1.5 bar to zero bar fairly quick, hence the red light comes on and it does not fire. The water comes out from the drain pipe under burner...

It is a very late update, I am so sorry. But after the vent pipes cleaned, its packed up again, engineer re-visited (free of charge) and this time he has changed the ignation BOARD. Thank you for the member, who has been saying this from the beginning. It has been OK since. BUT Today...

Fryer is Lincat DF618 twink tank with 2 x 9 KW elements. http://www.lincatequipment.com/product.asp?urn=1425&c_urn=183 I have used this fryer with my current 32A fuse. It did trip the fuse NOW and THAN and cables were worm. According EDF, they can not supply me more , because of my supply...

Hi, I am currently running my mobile burger van on 32 amp supply with no problems. However, due to an upgrade to powerful, single phase 2 x 9KW chip fryers, electricity board will soon supply me 63A for my mobile burger trailer. Other than the above mentioned fryers, I have large...

Sabre HE25 was working but cutting out now and then and red light coming on. I used to reset it, it then worked again. It went like this for few months. Recently, after I came back from holiday the other day, it stopped firing up all together. Pump runs, no red light comes on, infact...

Thanks BB, GG, Agile, DP. I will try to follow the flow chart on my user manual. Also, I am not too sure if all the parts will be same but we have another one of these boilers in the family, it is Sabre 29 HE. I can swap parts for testing purpose if any of you strongly suspect...

I got it fired up AGAIN by fiddling with the speed of the pump as the tap is running. (C/h switched off). Once it fires up, it works non stop as long as the hot water tap is on. When you turn the tap off, it may not work next time you demand hot water. It is too much of a coincidence...

No, as turned on the hot water tap, just before the stage it normaly fires, it cut out again and the solid red light is on. I am back to square one :( To Agile: - No, it was working (on and off with the fault) before I change the DWH sensor. I guess, the only other thing happened...

To BB, I have a SABRE 25 HE. Here are the sensors I have changed. As we agree, the one on the left is Primary NTC sensor, and the other one is DHW sensor (secondary sensor?) which I have just changed. If you look at the DHW sensor closely, you will notice the greenish deposits...

I think I have bought the correct sensors. After cross referencing part numbers, supplier gave me the two sensors pictured in my previous post. My receipt is below. Here is the bottom half picture of Sabre (Vokera) 25 HE. QUESTIONS: 1- I have already changed NTC...

To DP, Thank you for taking your time and writing. I do understand the principle of how the combi boiler or CH systems works. However, I do not have knowledge and special equipment necessary for checking and eliminating the components in order to diagnose fault like the qualified...

Thank you for all your replies. I am getting confused now. According to user manual, Solid Red Light fault indicates to NTC Primary Sensor and it is supposed to be fixed (screwed) on the right hand side of the main heat exchanger. I bought pair of sensors pictured below. I have...

Hi Agile, thank you for your advice. No disrespect to BB and GG who are currently helping me to solve my problem, but I was also wishing/waiting for your comments/advice on my problem too. I could not help noticing the amount of posts you have send to this forum as I was reading previous...

Thanks very much GG, I will follow your instructions tomorrow and will post the result. Just for clearity, you do want me to remove and bin the "DHW flow regulator" and run the system without this component? This means main water supply in to combi has to be by passed with something which...

Hi GG, I have already replaced Primary NTC Sensor = Primary Thermistor? The one you screw in with 13mm socket/spanner, on the righthand side of main heat exchanger. Is this primary thermistor? However, I could not find Domestic Hot Water flow regulator and Secondary Thermistor in my...

Minute ago, as I was washing up, I turned the hot water tap low, and combi cut out yet again. However, I get it working again by Reset ing it. Currently 144 views on my topic. Does it mean over 100 people have the same problem as mine and waiting for answer! This can not be right. I...

It start working yesterday, as I fiddled with the speed of the pump. I speeded up and put it back to number 1, as the hot water tap was on and it fired up. I wonder if this give you a clue about the fault?

Hi BB, When fault develops, it cuts out on Hot Water or when you put on Heating.

Hi BB, Thanks for pointing out the ignition board. Since I have managed to start it yesterday, combi has been working fine although I know it will cut out again soon, as it did in the past. Considering the new information above would you still say the faulty part is the ignition...