Search results

Thanks for info, was not aware of the T3 terminal connection being switched live, will need to rewire. Can you suggest any Honeywell stat as replacement?

The system was installed when I moved in, was not aware the bare CPC was being used for the live, thanks for the info. Will have to rewire the unit and boiler for new stat. Want a new stat as I know it does not always switch on when it gets cold, until its really cold even if I turn it up a...

Hi, I have had a T40 stat for many years and now want to change it for a digital stat, but not sure which stat to buy. I only want it to turn on and off the heating, nothing else ( like wireless, timer, app controlled etc), just a plain temperature controller. Also would like an easy to...

These show when I set programmer to always off for heating and hot water, or when I program the Heat and HW to be off and still uses gas

When I turned off the mains for the Central heating system so nothing kicked in, the amount of gas used was Zero, so I dont feel I have a gas leak or else it would have shown some used gas

I have verified the amount of gas used with the meter and its the same overnight, during the day the IHD shows it fluctuates and sometimes zero gas for some hours, I am sure its costing me more than it should, but dont know if its the programmer or boiler that is at fault.

My standing charge is 32p, which EDF told me would be there in the morning, the cost shown for gas is between £1.50 and £2 every morning, also I can see the energy used, every hour roughly the same amount

Its a Glow-worm 15hxi. If it is then its costing me £365 year to do this. I have read that this boiler will fire up if the temp goes below 3 degrees, but my house is always over 12 degrees?

Hi, I have had this BG DCP controller for many years (fitted by British Gas) and not bothered touching it as I thought it was working OK, however after having Smart meters fitted I noticed that during the night there was gas being used and charged for when the hot water and heating is programmed...

Many thanks for your continued assistance and perseverance, you have been very helpful suggesting things I need to test/check. It is around 8 to 10 years old so I think I need to get a new system. You have been a great help. appreciate it...

I have put it on this link, hope you can access it? https://drive.google.com/file/d/1Vz16DY-U6kM6rZJ-WG2cj3fZxg65A-5z/view?usp=sharing

I tried the transformer screws and they were tight. It is very loud, the bell is in my shed and the door locked closed, I can hear it from the front of my garden over 50 yards away. I made a video with the noise from my mobile but I tried to upload to this posting and it would not allow me to as...

I did a manual bell test and it works OK and makes the normal alarm siren, while in prog mode the buzzing noise of the bell stops, however when out of the mode it gives off the loud buzzing noise all the time. Took the cover off the bell box and the green and red lights are alternately flashing

I tested the battery with my multimeter, just the Voltage and not the current. The display shows normal Time and date etc, nothing unusual. The Event log shows mains Fail then Mains OK, for over last 100 entries, this was probably me turning the mains off and on, could not see any faults showing...

Sorry, the panel was still working when I turned off the mains, I could still set and reset when closing the door, it was just the bell keep sounding that stopped when I turned off the mains.

Thanks, I have just removed the battery in the main unit and measured the voltage, it was reading a steady 12.6V. I have read that the battery reads less than 12v when its gone? do you think it can still be dead? your reply is much appreciated.

Hi, I have installed the Accenta Mini G4 and bell in my shed, it has been working for a good few years with no trouble at all, just one trigger on the shed door. However today I could hear the alarm sounding and went into shed to find out why, the shed had not been broken into and when I tried...