Search results

Hello I want to change the radiators in my house. The current ones are imperial sized ones with odd sizes such as 1770mm, 1670mm, 1920mm and 1580mm etc. in width. To fit to the nearest metric size, I have this in mind:- 1770 - 1600 (extention pipe 90mm on each side) 1670 - 1600 (extention pipe...

Thanks Nigel.

Thanks Nigel. "just cuz the OP's in Herts". Sorry I am new to this lingual. What does it mean?

I have an old basin tap which is leaking and I want to replace the washer. Can somebody tell me how the top comes out. I have tried removing the 'C', hoping there would be a screw or nut underneath but I can't pierce it out. Does one have to lift the whole top in order to get inside? Thanks.

I am thinking of having a solid wood floor on the ground floor of my house. The floor is concrete and the house is approx. 30 years old. The shop from where I intend to purchase has advised me it can glued stright on the concrete floor. Is it OK to glue straight on the concrete floor or...

My installation manual for the Profile 100e shows more than 3 wires (live, switched live etc.). Which live and neutral on the S-Plan wiring diagram relate to the wire connection in the boiler.

I have the following system:- Fully pumped Potterton Profile 100e boiler Separate Honeywell motorised valves for heating and water Grundfos Pump Randall Timer Satchwell room thermostat Megaflow unvented cylinder Can somebody send or direct me to a wiring diagram for the above type of...

I just had to empty my heating system as one of the screw in the flooring boards had gone through one of the pipes and I wasn't sure whether if it was the water pipe or the central heating system pipe. I have now refilled the system by means of releasing the pressure valve in the system; I...

My present boiler is the garage and I have a Megaflo tank in the loft. The boiler needs replacing. I had a Corgi registered plumber come to survey my property. He said that there are too many bends in the pipes connecting the boiler to the Megaflo and the heating systems and it might be...

That's the valve which he opened and closed a few times. As to why he didn't diagnose the fault, he said the system should now be fine. Perhaps, I should get you to come and check out my system. Thanks for your quick responses.

Yes, it is a genuine Magaflo. Which is the 6 Bar relief valve. Do you mean the expansion valve? I have had a plumber who has already tried that but to no avail.

I am still learning about how post questions on the Forum. The picture are on http:/www.diynot.com/network/gillpeer/albums. How can one insert picture in the actual message?

I have a Megaflo CL210HE unvented hot water system. When the hot water is switched on, I get water trickling out from the discharge pipe. I have followed the procedure in the Installation Manual to recharge the air volume. When I do that, the system is fine for a few days, but then the water...

So is the wiring of the boiler incorrect or the megaflo wiring. As the boiler is heating up the water, it must be connected to the megalfo. How do I get in touch with D-HAILSHAM? What is a PM? Sorry for my ignorance of the terms used.

Exactly like your situation

Reply to Agile: The boiler is about 20 years old. I had the megaflo installed about 2 years ago and had a new pump and valves at the same time. The timer and the room thermostat are old. The problem I have has been there ever since I the megaflo installed. I have been too lazy to do...

Glasgowgas: it was easily rectified but the 2 scenarios sound similar to me. How was it rectified, please? twgas: What do you mean by "unless there's a frost stat." Thanks for the quick responses.

I have a Potterton Profile 100e boiler. Even when the programmer is not switched on, the boiler seems to come on every few minutes for a few seconds and then switches off. At the same time, the pump is hot all the time and makes a noise as if it is all the time. I have a megaflo system and a...