Search results

These old systems are prone to cold feed becoming blocked and boiling away the water. Check tank is full of water, if so open rad vent, no water means blocked cold feed. If there is water and pump valves are opened and can push finger in then either air lock or blocked pipes.

only a RGI person can go into testing appliance further

http://live.menmedia.co.uk/Event/Gas_explosion_in_Shaw?Page=0 The reason above and other gas explosions are rare is because of laws regarding installation and use of gas, something you are unable to prove your competent in so keep out of areas you lack recognised skills so we can keep the...

Correction joe I have 17th edition and part p in electrics field as well. Unlike you I do the training needed for areas I comment in.

Only if you work fast and no problems if there is your buggered. You can get a bung kit that makes a tanked system tempory sealed once you stick them in the tank pipes, and drain off the water presure, you are mostly dry part from some dribbling and gurgles now and then. Not fool proof tho.

Sounds like you need to stick a new pump in, with the tank being warm I suspect some sludge in system so a tub of system cleaner and a flush. Something you don't want to diy in cold times, but if the pump valves are like a gate valve with a shaft you may be in luck,if not a new set pump and...

It sounds like a flue/fan problem on the surface of what you say... but could be stuck valve not open flly pump or worse gas/air problem. Get the boiler on for central heating and turn the boilers ch stat down till the burner goes out. The pump should run on. If the nose stops the its a...

Welcome to the fun house. Please no more posts on this issue that do not help, op needs to get in a RGI to test the problems with their boiler

Boiler falls of wall snaps gas pipework customer returns home flips switch need 3 new homes there. Rodents climb into boiler flue not correctly fitted by non qualified person giving advice to take flue out to inspect but loosely refit it. Rodent nests inside blocks flue. Poc fill room...

Not always some well protected can be safe still, this is mostly down to movement which causes leak or people adjusting joints and not testing the joints as a RGI would know how to. Argument is won here you can dribble on will lol at the thread more in the cc section

Yes they start fires but are not as explosive if tampered with, this is normally due to overloading for falty installations components/tampering with. same thing with gas but gas flows out of a open pipe, where electrics wait for contact to earth. Also electrics has sieving with helps...

Ok electrics are deadly when touched and earthed. Gas from leaks fills a room volume with gas and a spark makes it go bang it can also follow the gas pipe work and blowup more then a single home such as the flats while back. Products of combustion can kill as well in homes away from the...

I have been to jobs with the boiler in bits as the customer tried fixing it them selfs one had a pilot going out on a pilot combi and as the ignition did not work he cut open the case and was using maches allowing poc into the room!! I asked why he said his m8 down the pub said to do it to...

The op needs a RGI simple as that, if you refer to the forum rules some aspects you can't comment on this being one of them. Joe has no gas certs as I am sure you do not. It's not a case of helping him its a case of untrained muppets like joe reading forum taking apart a boiler to try what's...

Not what you said here joe, all matters simple.

Seriously if you did even try the core domestic gas Cerys let alone all the commercial you see big part of the exams is pipe sizing, pipe work installation and other factors. Friction/resistance of pipe work and fittings is always taken into account. Basically it does affect the pressure at...

Try turning upstairs rads off and run heating, if they get hot see if any cold spots. Also chech small tank in loft for water and the colour and if its hot. If tanks hot its pumping over, cold spots in middle of rad both normaly mean system is smudged up if the pump is ok. Could also be...

Sadly most parts on this boiler are obsolete, think the timer is one I believe. You can wire a clock in but there will be a mess of wires, if you miss a wire or not wire correctly it can be hell to trace. As this needs the lower case removed and controls I suggest you get a rgi in to ensure...

http://www.hse.gov.uk/work-equipment-machinery/training-competence.htm Another link, if you need help I suggest you ask he's to clarify it for you... http://www.hse.gov.uk/involvement/competentperson.htm A competent person You must get help from a competent person to enable you to meet...

Joe you are wrong, First link from USA, the second uk. Non Rgi can not prove that unless taken all the assesments and have proven experience. Yes the links don't cover gas but it outlines a competent person as per eyes of law. http://www.osha.gov/SLTC/competentperson/index.html...