Search results

Ok thanks. Will investigate these vents.

Cold roof (insulation between rafters). How do over facia vents work if we don’t have any facia? Do we have to create it above the corbel?

We are in a 1930s bungalow and thinking of getting a loft conversion done. Roof is pitched and slated on all four sides but also has a concrete corbel running around the perimeter. The visible part of the corbel sticks out the wall about 150mm and has a similar depth. It may even be forming the...

Kitchen half of my kitchen diner is being refurbished and I want to install underfloor heating. The floor covering will be vinyl. Both floors are currently at the same level and the diner floor has a varnished finish. Problem is the foil heating will add a 13mm step between the floors so to get...

Concrete slab

OK thanks chaps. Looks as though the tank can be removed. A new toilet is getting fitted anyway so will ensure it has a high pressure inlet. Thanks

The tank supplies the toilet, bath and WHB but I thought I could connect these to the mains. Not sure of the boiler make but it is not a Worcester. The tank is inside the flat about 6m away from the boiler (and about 1m above the the boiler level).

My kids stay in a 2nd floor (of 3) flat which has a combi boiler. However it also has a cold water storage tank which appears to be leaking and I thought about removing it. Is there any reason why this tank would have been retained when the boiler was installed (other than saving time and money)?

This model has an ice maker. The flap which opens to dispense the ice has come loose and it appears you need 10 inch fingers with multiple joints to refit it. Does anyone know how you access this? I'm sure the front control panel must come off but afraid I might knacker it if I try to force it.

Thanks Gordongas. It's worth a try.

It appears I need to change this valve (and the one above the pump). In mitigation I never installed them in the first place. I was hoping I could get away with a bodge to stop the leak for the 3-4 months before the new system is installed. Is this out of the question? If I need to change does...

OK Thanks. Found one for a tenner which should do the job.

Thanks for the feedback chaps. When I say a spindle I really mean it's a stump of metal sticking out no more than 2-3mm from the valve. There is no gland nut. The spindle sems to be part of a cylinder recessed in the valve body, no more than about 8-9mm diameter. Water is leaking out between the...

Thanks Trevor. Don't suppose you know where I can lay my hands on one. Just done a quick search but the prices vary wildly from around £5 to about £25 and I'm not sure thay are all the same thing.

During my investigations to find out why my CH wasn't working I isolated the pump by turning off the two valves either side of it. I never actually removed the pump (nuts were so tight I gave up) but unfortunately there is now a small leak from the downstream valve and it looks like it may have...

I think this valve is the reason I have no CH. I have read it is possible to change the motor/actuator but I cannot find any details about this model. The V4043H seems to be the standard Honeywell part. Was the 4013H replaced by the 4043H and can I use a motor from the 4043.

Try here Move the horizontal slider almost to the middle and you will see chrome, brass and satin 50A DP shower switches.

Not only can you not isolate it but you are using the main stair fuse as circuit protection. If a fault develops in your shower it is likely to take out the whole stairwell. Get it sorted. The REC will fit an isolator before your CU free of charge - certainly in Fife they do.

Thanks Zampa. Sounds good.

I've just had 6 new internal doors installed which are advertised as oak foil veneer (paper foil technology). They look quite impressive (for the price) but I would like to paint the inside of the bathroom door gloss white. Any things to look out for in the prep or is a light sanding and...