Search results

I have a Ergo Laptop with a VGA port and a TVout RCA jack. My problem is that if i connect an external monitor or tv everything seems fine except that if i play a film whether it be in media player , bs player etc the film will not display on external screens but fine on laptop screen . desktop...

there may be an adjustable flap at the back on the right hand side , make sure this is not down as this is used for liquid detergent and can cause your described problem if used with powder

this is usually caused because the syphon tube is blocked , remove drawer and clean thouroughly paying particular attention to the syphon tube and the channel that leads off the syphon tube on the underside of the drawer .

a boil wash is recomended by most manufactures occasionally , helps to disperse the build up of sludge left behind by modern day 40 degree washes . i always advise people to do a boil wash once a month , just add normal dosage of detergent or descaler/cleaner and run without a load . And as...

part you describe is called a cradle , there are 2 different ones for this model dependent on serial number , up to serial no 30127.0000 part number c00066074 , after serial no 30127.0001 part number is c00093878 . can be obtained from indesit direct and are not too expensive either

try pressing and holding the power button for 2 seconds

what make / model is your d/w

your problem is that new modules come without an eeprom )little microchip programed to your specific model) these can be ordered from indesit pre programmed to your specific model , or you could call out an engineer from indesit who can install a blank eeprom and program it via his laptop

dont know if this will help but E90 is a user error code which can relate to one of two alarm code , E93 and E94 E93 is a machine configuration error E94 cycle configuration error Both of which point to main board being faulty as it would be unlikely that you have reconfigured the...

CHECK THAT THE DRAIN HOSE IS NOT TOO FAR DOWN THE OUTLET PIPE (ONLY NEEDS TO BE 6" ) AS THIS CAN CAUSE THE WATER TO SYPHON OUT WHILST FILLING MOD please see item 6

sounds like a ceased circulation pump to me

is this a capacitor or is it a mains filter ???????????? what wires go into the conponent

if you listen closely when the machine seems to be going round its cycle , can you hear a buzzing sound , if so i would say the circ pump has seized up whilst in storage

its more than likely thayt the machine has overfilled and actuated the aqua stop ( float operated microswitch ) in the base of the machine .this can be caused by numerous situations and i would advise that you get an engineer to check the machine as the circ pump often gets wet in this...

firstly there are several different modules for the WMA range although they probably look identicle. on the module there will be a label . it will be either red , yellow , white etc etc and you need to make sure the one you fitted is the same colour lable as the one removed and from the...

is the machine still drying as efficent !!!!! if so i would say that the so called engineer is trying to pull a fast one . Ok you can get a bit of fluff build up in the condenser and a bit in the heater box but in my experience modern day machines ie. WD62 do not suffer from fluff build up as...

there is a drum lock on these to stop the machine from spinning whilst lid is open , sometimes the white peg on the lid breaks off check this first

you will first need to find out which outer tank is fitted to machine as this machine was built with 3 different ones WG1034TPG WAS A PLASTIC TANK , WG1034TGT WAS A METAL TANK that had a seperate front plate and the WG1034TG was built with a metal tank that had a removable back plate . if...

if this is a hotpoint then yes it is a power unit (gearbox) fault. The power units for hotpoint top loaders were made obsolete about 6 months ago so no point in calling an engineer

the wma32 has out of balance detection , check that a suspension leg retaining pin has not come out and also check both weights are not loose