Search results

Cheers Guys, Tank cannot be that old looks like it was installed early 80's. So Tank cutter it is, cheers for the input. Gary

Cheers Harry, will give it the old tap test, see how thick it sounds. Gary

That's what I keep finding when I have trawled the web, must be an oldie. Gary

I certainly can, Here you go. Gary

UPDATE So it seems for some reason on part set the pir that was not activating takes longer to kick in when compared to a full set, put the sensor on alway awake and it triggered straight away, put it back on auto, and it takes around a minute before it will trigger on part, when on full does...

I will start with the suggestions above, always difficult if you don't see the whole picture as to how it has been setup when not infront of it, just thought I had missed something, I may have done. No wintex attached to this one, so all done via the keypad, which in itself is fun. Cheers for...

Fiddling, more setting up I would say, with a small niggle. Yeah triple checked the settings in zone programming, only option I could see for a zone not to operate under a part, is if the attribute is selected to omit it from the part arms, could not see anywhere else it could be. Cheers

Now that is a good idea, will set to always awake, just to see if it a makes a difference. Without sounding too dumb, what do you mean by programming ? as in zones types, global options ? Cheers

Will give that a try, but when it's fully armed, I can leave it 10 seconds and it will trigger off, not sure why part arm should be any different. Might delete the device and relearn it, see if it makes any difference. Cheers

Got me there, not on site at the moment. All the devices show up on the walk test fine. As for zone programming, you need attributes or types, basic setup, one area, installed are two Micro Contact W's, and three Premier Compact PW-W 1 door mag setup on exit /entry, all other devices set to...

Morning Guys, Got a weird issue when part arming the above, only one area set on the alarm which covers all sensors, full arm works a treat no problem, when part arming, the sensor that is omitted on the part arm works as it should, but another sensor which is in the living room is also been...

Guys, Hi have just installed a Pyronix DeltaBell + to replace my old belle, this works no probs, I have used the old belle as a second bell box, it was my understanding you could wire in bell +, bell -, bell trigger and strobe all in parallel and the tamper in series, When I do this all is...

Guys, I have got a QVIS Universal NVR running the latest Cortex software, there are two Qvis PTZ cameras attached to it, and I have added a further 3 Hikvision cams, the hikvisions work fine no lag on preview or playback, but the Qvis PTZ seem to be dropping in and out of connection, the...

Guys, I have a condenser dryer which now after doing a cycle, seems to produce a lot of water at the front of the dryer below where the filters are, I thought it was the pump at the rear, so checked all that and even replaced it with a spare, that seems to do its job and pumps water up to the...

Guys, As the subject says, I have Home easy ultimate sockets, boiler switch and light switches. I was just about rip them all out and replace them with some lightwave rf kit. Then I thought can this system be made smart, spotted a few things that will say it will work with this kit, but does...

Spoke to soon, as I posted this the nvr detected the cam, got the mac address, it has assigned an IP, but moaning about login, used the onvif details there, but doesn't like it. will keep going. Gaz

Guys, Turned on Onvif, set the username up, checked the port no, default is 554, set the ip manually on the cameras, pointed the NVR at it and still doesn't see it, the two existing cams on the system are on a different ip range which looks like it was setup by the previous user, I have given...

Nope they are Oyn-x ones. Yes the login details are the same, the option is actually there for that when adding a new IP cam. That's what I do on the hikvision stuff, match them up and off they go, simple. Certainly will try that option, back up there on Friday, will keep you posted. Cheers for...

Bianco, I will give that a try, port 8000 is the management port, I just checked my Hikvision box. Gaz

There are two PTZ's plugged directly on the system already, I am adding three 4MP hikvision cams directly to the back of it, as it supports up to 16 IP cams. I matched the Hikvision IPs to the next available ones after the already working PTZ ones, there is an option to search for ip cams on the...