Search results

Hi I need to put plywood onto my kitchen floor to bring up the level, can I screw and plug straight through the bitumen or do I need to fill the hole water a waterproof substance first? Thanks

Thanks for more free advice would i be right in guessing the the secondary and DHW heat exchanger being the same thing :D

thanks for the free info, would that noy also affect the CH

Hello all I have a problem with my boiler it works fine with the heating on but when hot water is called for it run for around ten seconds then them temp gauge shoots from 60 - 90 degrees very quickly then trips out and has to be reset with the red button. i am not sure but if there is some...

thank you this is the fire we are going to get http://www.dunsleyheat.co.uk/yorkshirestoveCH.htm

thank you for your replydo you have to have a doubled lined chimney? i have seem thermal type block and twin wall stainless steel flue can these be used on there own or would they have to be inside the chimney my understanding of it is that it needs to be douled skinned to retain the heat so you...

thank you for your reply do you have to have a doubled lined chimney? i have seem thermal type block and twin wall stainless steel flue can these be used on there own or would they have to be inside the chimney my understanding of it is that it needs to be douled skinned to retain the heat so...

hello i am thinking of getting a log burner but am a little stuck where would be the easiest place to put it. we have a gas fire in the front room and from what i can tel it seems to be a concrete block chimney/flue (not visable inside or outside the propety) with a steel flue in the loft...

hello i am thinking of getting a log burner but am a little stuck where would be the easiest place to put it. we have a gas fire in the front room and from what i can tel it seems to be a concrete block chimney/flue (not visable inside or outside the propety) with a steel flue in the loft...

thanks i will do

hello i am building a deck wich is approx 400mm off the ground what is the min depth of the posts the ground is full of brick clay etc, the posts are 860 betwen centres also what is the max between the posts many thanks chris

to be honest the house has not had any extras i did it up, we had a combi fitted so there is no immersion there is no supply to the garage cos i pulled it out there cant be much else

thank you industryspark ban-al-sheds for that info i have no probs with getting it done but the house has been up for sale for 6 months it costing me alot once there is someone in it then it could be something to look at

thanks JohnD i was just a bit comcermned about the cost of fitting a new cu. the old one is as you described (without the nails i used screws just kidding) as the man that came round siad you need this and i could see that turning into the other just did not want to be stung my fiance was there...

bs7671 is a non statutory document so it cant be 'the law' to install rcd's. thanks for that its what he told me we never went fully into the regs cos it was three days my job is a lift tech and we needed the regs for testing new installs but only the lights and the wire between the isolator...

Not quite yet. And even when it is there will be no compulsion to bring old installations up to date. thanks for that so would a need a cert which says landlord on it cos i do have the other. the reason why i ask is the gas says landlord safety check on it. do electrics need checking...

from memeroy i think that there is a 6a fuse for the lights two 32a rings and a 20a for there cooker there is no electric shower i am just wondering if they would have to split these circiuts into more ie two light circiuts like you have with more modern cu`s

sorry he did all the readings and they must have been fine cos on the cert it says it should be retested in 10 years. i really wanted a lardloads cert but there was a bit of confustion and he did a safety check

everything was safe but he recommeded a mcb type cu, and then said you have to have it if your renting the house out. he did not find any faults. i am just wondering if it is reg to have that. obviously its safer to have rcd protection but is it law. i have done then 16th but it was 18 months...

Hello i have had a electrical safety check done 8 months ago, i was thinking of renting the house the guy told me it would need a rcd type cu it currently has a fused cu it has 4 circuits would it be a case of just changing the cu or would the circiuts need to be split. i will get someone to...