Search results

Not had the time to get back to this....a bit lost tbh....can i not configure just the speaker in the garage to go off..?

Started going through the manual (not really sure what im looking for) the expander has a cable marked "int speaker" with just a red and black wires being used in the cable...its quite busy but the bell boxes appear to be going towards the right hand side of the elite panel...

Ok - initially i dont understand that but ill consult the manual and trace how the panel is wired up....probably best establish what ive got an understand that first....didnt get to it last night as car battery had to come out for a charge!! Theres that grade 3 again... (whats that then) is it...

ok- ill check the wiring tonight...in the office during the day...thanks. Just to ask - im assuming each bellbox should be in its own zone on the alarm panel? And....my expander only has a couple of zones used...so if need be i could move one of the bell boxes over to that...?

Ok. thanks....pretty sure bellboxes are wired into the main panel (these are the bellboxes [2of them] at the front and back of the house....i do have a siren inside the front door and one in the garage...that being said if if someone broke into the garage i would want just the siren to go off in...

Right ok....totally lost..! So the pir is on zone 5 on the expander (but not configured) Doesnt the expander wire into "network" on the main panel? - so not in a zone as such [ when i transfered the panel over i didnt mentally make notes of what was wired to what...] just concentrated on the...

Hi there. In the interests of keeping things separate ive had some very valuable and great help on here so far with my newly replaced Texecom Premiere 48 alarm panel (just updated to the latest version) with great help on here and from texecom themselves ive managed to get a second hand...

Brilliant - thanks very much. I think one of my pir's is going....this one above - is this the best type to get [easiest to wire in] or is there another one you would recommend? Thanks for the continued advice and help! Edit - thats now wired in on the extender on Zone5 - ive been into the...

Ive mains wired my whole house up and installed a 48port Lan switch....more than capable.

Thanks for the reply, ok - i dont understand all of that, so, i take red and black wires to the "output" on the expander [ thats the power out, i think ] take the tamper wires to the zone, and am i right in thinking that i put a loop in there as well? [ in two outputs in the zone ]?

Been tracing the wiring in the garage tonight ive done the above and wired the pir end as the above pic....so im planning on wiring this into the expander - im just looking at what i think are the PIR's that are alread attached to the main premiere....so the zone (for example for the kitchen)...

Righty....i understand that....i think the main panel is full (ill have to double check) but theres loads of zones on the expander next to it...so i find a zone on the expander and then wire those 4 into a "zone" - where do theresistors come into it? Oh little bit of a side-question....so i can...

Lol - i have no idea what any of that means!!

Pics from my phone...

Yes - looks like another one....i have looked through the other threads and cant see mine....this was left behind by the installer...im presuming the usual + - and the two tamper wires...but this pir isnt marked out with the latter wires labelled??

Well, just to summarize this ive got to the end...(of this thread)! I spoke to a lad this afternoon at Texecom and he was incredibly helpful (and has been over the last month) hes always replied to my emails - so the reason i couldnt get it with my app but he could so could have been my...

I did try that "5678" but that didnt work...i did set the master in Wintex and send it over but that didnt work either? could it be the SmartCom firmware is maybe out of date/too far behind the new panel? Can i use the engineer code or must it specifically be the master code? In WinTex is there...

What do you mean by "Non elite"? its and elite 48-W so im learning here! :)

As above....kinda moved on a stage from my installation thread. Ive got an installers code, ive got a code from the panel for the SmartApp - logged into the app (account setup), created the site, added the installers code - im at the point where it wants the "Panel User Code" - no matter what i...

Ah - righty...ok - so my old one 9.03 is useless? Not to digress too much but a panel i got with a SmartCom - an Elite 48-W i flashed with the latest firmware....so thats good for all the latest stuff/functionality?