Search results

! am replacing my single tap kitchen sink unit with a two tap sink unit as I was told it would help the speed at which my taps would then deliver water from water tank in loft. I am looking on the internet at Clearwater stainless steel sink unit with two tap holes and roll front 1000 x 600. My...

I have just got a fluidmaster cable dual flush valve for installation. What I cannot understand it has a partial flush adjusting slide which has more/less marked numbers 1 to 12 but the slide will only move up to about 3 but then falls back again. Also on the other side marked more/less 1 to 6...

I have just got a fluidmaster cable dual flush valve for installation. What I cannot understand it has a partial flush adjusting slide which has more/less marked numbers 1 to 12 but the slide will only move up to about 3 but then falls back again. Also on the other side marked more/less 1 to 6...

Hi First have you checked to see in your windows updates whether you have download update 7.6.7600.320 or windows 7.6.7600.256? My problem was due to when it downloaded Windows SP1 update 7.6.7600.320 replaced 7.6.7600.256. which I found many other people had exactly the same problem...

Hi yes this solved my problem but yours might be something different. I found this information from other sites: If SP1 and Update Client 7.6.7600.320 takes over. The only glimmer of light came when I downloaded updates KB3102810 and KB947821 and I then was able to download/install nearly a...

I had been looking at FlushKING Complete Repair Pack 1 or 2, but you have suggested Fluidmaster Pro45B, which I will have a look at. I hope you don't mind but have you any experience of Flushking repair pack. Many thanks for your reply. Dugit

TOILET SYSTEMS bottom entry valve : For bottom entry fill valve is it a real advantage/helpful to have an adjustable height over a fixed 8 inch height?

I measure from the bottom of the water tank to the top of the upstairs wc cistern to be a little over 60cm so about 0.06bar so it might be a problem. Anyway many thanks for your reply. I will have to think about it. If I do the downstairs wc first , I could first try a separate test connecting...

My present toilet system upstairs and downstairs operate not from the water mains supply but from a tank in the loft and when I installed them a good few years ago I had to fiddle with the water inlet to allow the water to fill the bowl. I’m looking at a replacement Flush King top flush...

Have recently downloaded and installed Windows 10 (from Windows 7 64 bit) on my Medion pc. Two days later I then tried downloading Windows 10 on my wife's Medion pc (from Windows 7 32 bit) and I could not get it to download, my wife said she had not had any Windows updates to install for some...

I have a Triton Jade 1 shower. When switched on it has just started to leak water from the plastic tube which is situated just behind the water outlet to the showerhead. I have read that it may be a faulty prd and o ring 83301330 but this looks difficult to get at (I have disconnected the power...

I have an Armitage Shanks AMSTD FASTPART flush valve for toilet and require a rubber seal washer to replace mine which is leaking, the dimensions are OD 80mm ID 56mm and thickness 3mm.I have been unable to find one after looking everywhere. Any advice on where I could get one would be...

Apologies for the question I have found that the electrical leads were holding the motor tight. Have removed the motor now. Sorry again

Removal of motor to change the brushes on washing machine I am trying to take off the motor of Bosch WFF 2001 GB/01 to replace the brushes. I have removed a 4cm bolt from the front and a 2cm bolt from the backside but the motor still seems fixed as where the 2cm bolt came from there is still...

I intend to change my T12 2x 40watt fluorescent light fitting to take T8 2x 36watt and my question is whether the type/make of T8 ballast is important, any advice would be appreciated?

Many thanks for the replies which make sense. dugit

I was cleaning out my fire grate of all bits and decided to look up the chimney to see if it was clear but I could not see daylight at all, should I be able to ?. I just have the one fireplace which seems to go straight up or do chimneys have a step in them.

I have a colour tv panasonic TX-W28D2DP and it is stuck in stanby mode and I cannot get out of it whatever I try. Any suggestions would be appreciated

I have just had a carpenter install an mdf doors and shelves bedroom wardrobe and am considering how to finish off the mdf. I have looked on the internet about mdf on what to do but I am not sure so I’m looking for advice on the best method etc. I want the doors to be white (satin) and do I...

Have removed the Photo 915 and made the Copy 1 as default and it seems to be printing ok. The printer in devices and printers still has yellow exclamation mark. Anyway hope it keeps printing.