Anti-Freeze in UnderFloor Heating

It used to be insurers insisted on a minimum temperature of 12C although my insurance is with Admiral and they say I have to take reasonable care and leave the heating on or drain the system if I am away for an extended period in the winter. I set my fallback temp to 18C when at home and 16C when we are away to avoid anything freezing.
 
Thank you for your advice.
Unfortunately the UFH is not yet in commision, and that part of the building (in process) is not yet occupied.
But the pipes are charged and maintaining a good pressure, but the circulation pump has not yet been used.
The floor has been screeded.
 
Sixteen degrees Celsius? To avoid freezing?

You do know what temperature water freezes at, don’t you?
I have a well insulated modern house with a fair bit of solar gain but incredibly slow heating response time (ASHP into all UFH) so my min temp costs very little extra on top of the insurers 12C limit and ensures pipes buried in walls and floors (still within the thermal envelope) are never at risk.

The 16C of course measured by stats mounted in rooms far from some of the pipework. Having experienced frozen pipes and the aftermath, I'll stick with my method as the energy cost far outweighs the risk of setting 12C only for a utility room pipe against an outside wall to freeze in a cold snap.

Other benefits, no damp, no musty clothes, faster warm up when we get home etc.
 
I have a well insulated modern house with a fair bit of solar gain but incredibly slow heating response time (ASHP into all UFH) so my min temp costs very little extra on top of the insurers 12C limit and ensures pipes buried in walls and floors (still within the thermal envelope) are never at risk.

The 16C of course measured by stats mounted in rooms far from some of the pipework. Having experienced frozen pipes and the aftermath, I'll stick with my method as the energy cost far outweighs the risk of setting 12C only for a utility room pipe against an outside wall to freeze in a cold snap.

Other benefits, no damp, no musty clothes, faster warm up when we get home etc.
Well that has answered my first question, "do I need it" Obviously I do.
Now all I have to figure out is what sort of antifreeze do I use, and how di I get it in.
 
Well that has answered my first question, "do I need it" Obviously I do.
Now all I have to figure out is what sort of antifreeze do I use, and how di I get it in.
I don't think you need it. What do your insurers say? I expect they'll want 12C or drain. Even if they say "reasonable care", I'm not sure they'll accept non standard methods.

Heating systems need inhibitors to protect against mixed metals reaction, not antifreeze.

Don't forget a lot of home damp issues are caused by insufficient heating.
 
For anyone interested I have found the answer thanks to advice given on another DIY site.

Any freezing of the pipes is unlikely to occur under the screed. But the maniflod and above ground pipes are susceptible to freezing in an unheated building.
Once the amount required is calculated and mixed with some water, this can be put in a pressure test pump, designed for testing UFH, like this one:

Using a second container to catch the evacuated water, inject the antifreeze-water mix into the UFH.
When the last of the plain water is detected coming out of the pipes, allow any further discharged water to go into the Pump pressure tester tank.
Continue this process until the ejected water-antifreeze mixture is is about the same colour coming out of the pipes as that going in.
If you can then run the pump to further mix the water -antifreeze in the pipes.

I am advised that some ASHP or GSHP suppliers might be specific about which type of antifreeze is used. So if you have a Heat Pump already connected, check with the supplier on the use of antifreeze.
 

If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.

Select the supplier or trade you require, enter your location to begin your search.


Are you a trade or supplier? You can create your listing free at DIYnot Local

 
Back
Top