DIYnot > Forum Author Search

Forum Search by Author

Results 1 - 10 of 184 for bikerm4.

it works, its normally used on rough tracks or unadopted roads to give a more even surface or areas to park cars on. Suppose it matters what depth the scalpings are put down at and what the ground underneath is like.

bikerm4 | In the Garden | www.diynot.com/forums/viewtopic.php?p=1238793#1238793 - 29 May 2009 8:25 pm

Re: Chippings instead of hardcore ?

Ive seen this done in some ares. Tarmac scalpings are laid down then diesel sprinkled over them which softens the tarmac, then they are rolled or wackered. When the diesel has evaporated/ soaked in the scalpings harden up again. Smells of diesel for ...

bikerm4 | In the Garden | www.diynot.com/forums/viewtopic.php?p=1238655#1238655 - 29 May 2009 5:25 pm

Re: vauxhall vivaro door open warning light on

Same happened on mine,turned out the rubber grommett that compresses the switch on the back door had fell out.

bikerm4 | Car Repairs / Maintenance | www.diynot.com/forums/viewtopic.php?p=1153602#1153602 - 27 February 2009 8:09 am

Re: vivaro van

my 56 reg primastar, basically the same van, was recalled recently for changes to a handbrake linkage and to change the position of some wiring in the engine compartment i think which could rub against something and chaff through and cause a possible...

bikerm4 | Car Repairs / Maintenance | www.diynot.com/forums/viewtopic.php?p=1132839#1132839 - 7 February 2009 9:49 pm

Re: Sealing damp walls with pva before rendering

Think your first mistake is calling builders dumb. You then decide you can do it better and from your post its clear you havent a clue what to do. Also please explain what a solid cavity wall is. Reading your previous posts it seems your more than li...

bikerm4 | Plastering and Rendering | www.diynot.com/forums/viewtopic.php?p=1026860#1026860 - 14 October 2008 11:16 am

Re: Should I be worried?

The soldier courses above the windows are built on 100mm angle iron. If you look carefully you can see the edge of it set back slightly above the window.

bikerm4 | Building | www.diynot.com/forums/viewtopic.php?p=1024299#1024299 - 10 October 2008 8:49 pm

Re: plastic fence posts and gravel boards

They sell them here, never used them though. http://www.estatesawmills.com/products.php?cat=305&parent=31

bikerm4 | In the Garden | www.diynot.com/forums/viewtopic.php?p=1001409#1001409 - 13 September 2008 7:12 pm

Re: DIY chimney lining?!

Just seen that fluesystems have now started making gather hoods to size. I have had to make my own in the past out of tin sheeting or fireboard, these seem a lot easier http://www.fluesystems.com/liners/info/chimney_liner_gathers.htm Have you conside...

bikerm4 | Building | www.diynot.com/forums/viewtopic.php?p=990218#990218 - 31 August 2008 5:58 pm

Re: DIY chimney lining?!

Ive done a few of these. Some liners sail down the flue, others are a right sod, tight bends to get the liner round and blockages to remove. not a job for anyone inexperienced working at heights, its not easy on a roof with 8 metres of lining that ne...

bikerm4 | Building | www.diynot.com/forums/viewtopic.php?p=989987#989987 - 31 August 2008 2:47 pm

Re: hoover for brick dust

Ive got an old dyson i use. They have got a safety cut out on them which trips in if its very dusty. I phoned dyson cos i thought id burned it out, they said it takes between 5 minutes and 3 hours for it to re-set itself. Took mine 3 hours :roll:

bikerm4 | Building | www.diynot.com/forums/viewtopic.php?p=988505#988505 - 29 August 2008 2:49 pm

Result Page: 1 2 3 4 5 6 7 8 9 10 Next >

Find an Expert | Find a Supplier | Search DIYnot.com
Network | Advertising | Newsletter

By using this site you agree to our Terms of Service / Disclaimer.
Please read our Privacy Policy.