DIYnot > Forum Author Search

Forum Search by Author

Results 1 - 10 of 629 for neds.

Got the Dewalt extreme2 set. They are good but never had a 7mm or 5.5 mm bit in the set. Bought these for a couple of quid each and the set is pretty good.

neds | Tools and Materials | www.diynot.com/forums/viewtopic.php?p=1411586#1411586 - 18 November 2009 6:42 pm

Re: Cheapest place for BAL WP1?

Cheers. I havent really looked at other solution other than Bal, but wiwll check them out. Tilefix seem cheaper too howewver I'm sure people were getting this for about ther £50 mark? Whats the Dunlop kit like from Screwfix? it doesnt seem to have en...

neds | Tiling | www.diynot.com/forums/viewtopic.php?p=1411580#1411580 - 18 November 2009 6:38 pm

Cheapest place for BAL WP1?

Need to tank my shower area with the WP1 Showewr proofing kit. The only place local to me that seems to sell it is Topps Tiles and they are doing it for £75! I'm pretty sure some people were able to get it for much cheaper but was not sure where from...

neds | Tiling | www.diynot.com/forums/viewtopic.php?p=1409992#1409992 - 17 November 2009 2:17 pm

Re: New Combi Drill 18v ( Good Deal )

You wont go far wrong with that drill and its a very good price. The reason its cheap is because it comes with 1.3Ah batteries. Not really a problem though as you get 3 and the charge cylces are not that long either.

neds | Tools and Materials | www.diynot.com/forums/viewtopic.php?p=1407130#1407130 - 15 November 2009 12:34 am

Re: Toolbox vs Toolbag vs Tote

I got a Tote as my main tools holder. Its perfect, Its a real long one with loads of pockets, each tool has its place, no more rooting round the bottom of the tool box for that screwdriver!

neds | Tools and Materials | www.diynot.com/forums/viewtopic.php?p=1403677#1403677 - 11 November 2009 11:20 pm

Re: using a hand plane - any tips

You need a lesson from David Charlesworth. :wink: If there is another word for perfectionism that man should have it in his middle name!

neds | Tools and Materials | www.diynot.com/forums/viewtopic.php?p=1402507#1402507 - 10 November 2009 10:53 pm

Re: Bathroom walls

Both are cement based and water resistant to an extent, and yes you would use these in place of plasterboard. But for the cost just board with regular plasterboard and tank it.

neds | Plastering and Rendering | www.diynot.com/forums/viewtopic.php?p=1401378#1401378 - 10 November 2009 12:25 am

Re: plaster board or plaster on to brick?

Along with the Dot & dab use some mechanical fixings too. So basically once you have dot & dabbed the boards in, wait till they set then drill holes straight through the P/B into the brick. Pop a wall plug in and screw the board to the wall. Will giv...

neds | Building | www.diynot.com/forums/viewtopic.php?p=1401269#1401269 - 9 November 2009 10:46 pm

Re: Circular Saw

I got a similar sized 12V Makita circular saw 5093 and find it perfect for ripping up floor boards/chipboard as it has just the right max cut of 1 so no adjusting necessary.

neds | Tools and Materials | www.diynot.com/forums/viewtopic.php?p=1395350#1395350 - 4 November 2009 10:56 pm

Re: installing cold water feed for washing machine in garage..

Also while you're at it check behind that wall that feed for the external tap needs to have a double check valve fitted. If not good time to add one in line.

neds | Plumbing and Central Heating | www.diynot.com/forums/viewtopic.php?p=1390098#1390098 - 1 November 2009 1:05 am

Result Page: 1 2 3 4 5 6 7 8 9 10 Next >

Find an Expert | Find a Supplier | Search DIYnot.com
Network | Advertising | Newsletter

By using this site you agree to our Terms of Service / Disclaimer.
Please read our Privacy Policy.