DIYnot > Forum Author Search

Forum Search by Author

Results 1 - 10 of 119 for simonpolly.

The incoming cable is called cad55,it has 4 pairs and is used where the end user has more the 2 lines normally , Just a thought you mentioned that the line went off after they installed adsl broadband,adsl does not need installing which leads me to t...

simonpolly | Alarms, CCTV & Telephones | www.diynot.com/forums/viewtopic.php?p=1414962#1414962 - 21 November 2009 4:58 pm

Re: Phone line extension help

:P I work for openreach and even i`m confused ,too much info already :

simonpolly | Alarms, CCTV & Telephones | www.diynot.com/forums/viewtopic.php?p=1395123#1395123 - 4 November 2009 8:51 pm

Re: IP signalling

So if the computer at the remote site that is linked to a alarm loses its internet connection or complete loss of phone line,how long before it alarms ?,i`m only interested because i sometimes install redcare onto peoples phone lines and know that it...

simonpolly | Alarms, CCTV & Telephones | www.diynot.com/forums/viewtopic.php?p=1386087#1386087 - 28 October 2009 5:41 pm

Re: IP signalling

How does IP signalling work ?

simonpolly | Alarms, CCTV & Telephones | www.diynot.com/forums/viewtopic.php?p=1385694#1385694 - 28 October 2009 9:59 am

Re: Manual for BT301C "Mole"

They are a great bit of kit particularity if you're dealing with faults on long/awkward access runs, a 9083 and a tone tracer will get you through most faults but the TDR pinpoints the problem. I've used it on coax too works just as well. Have you al...

simonpolly | Alarms, CCTV & Telephones | www.diynot.com/forums/viewtopic.php?p=1384663#1384663 - 27 October 2009 3:49 pm

Re: Broadband connection

Contact your service provider and ask for a open reach engineer to do a SFI health check and a pair quality test,this is a indepth test done from the nte using the B.T hawk tester a laptop and the remote emulation equipment in the exchange,if it pass...

simonpolly | Alarms, CCTV & Telephones | www.diynot.com/forums/viewtopic.php?p=1379194#1379194 - 22 October 2009 6:56 pm

Re: Telephone extensions wiring (diagram)

If you use a adsl faceplate the adsl signal will stop at the master socket and you will have to plug your router/hub into the master socket,you can the run the extensions as per your diagram but there will be no adsl signal at them.Why not go wireles...

simonpolly | Alarms, CCTV & Telephones | www.diynot.com/forums/viewtopic.php?p=1370708#1370708 - 15 October 2009 5:29 pm

Re: Do I need to connect to a BT413A

If its a openreach nte you don`t need to remove the bell wire as the nte has a built in bell wire filter,if there was no filter just a piggy backed double connector then that will be why the bb was dropping out when the phone was used. just looked at...

simonpolly | Alarms, CCTV & Telephones | www.diynot.com/forums/viewtopic.php?p=1353359#1353359 - 1 October 2009 6:52 pm

Re: Do I need to connect to a BT413A

Have you run a extension into the boys bedroom or is he using a long ethernet cable ? and you need a filter on the master and extension socket

simonpolly | Alarms, CCTV & Telephones | www.diynot.com/forums/viewtopic.php?p=1351716#1351716 - 30 September 2009 4:37 pm

Re: Twisted Pair Cables — How Twisted?

:P the days of split pairs are long gone now,PQ and eclipse picks it up everytime,nothing worse than faulting a new line then it coming up unbalanced cable.Working for bt its easy to get confused from time to time. :lol:

simonpolly | Alarms, CCTV & Telephones | www.diynot.com/forums/viewtopic.php?p=1349358#1349358 - 28 September 2009 6:31 pm

Result Page: 1 2 3 4 5 6 7 8 9 10 Next >

Find an Expert | Find a Supplier | Search DIYnot.com
Network | Advertising | Newsletter

By using this site you agree to our Terms of Service / Disclaimer.
Please read our Privacy Policy.