It's dried blood - splashed there and ran down.
What size do you think these tails are
- Thread starter ceraunic_level
- Start date
- Joined
- 11 Jan 2004
- Messages
- 45,848
- Reaction score
- 3,514
- Country
My wizened old eyes reckon that the outgoing tails are of different csa's.
Looking at the age of the installation I'd be inclined to say 16/10. You didn't generally see 25 used domestically until relatively recently.
I have the same meter at my property which was built in the mid to late 70's.
Both incoming and outgoing tails are 25mm2.
Both incoming and outgoing tails are 25mm2.
Interesting - maybe its a regional thing.
Certainly, down here in the WPD area (old South Wales Electric), they only fuse to 80A, and balk most definitely at the idea of a 100A supply - according to company policy they will not fit 100A as they reckon the cutouts (modern ones that is) can't take it on a sustained load. I had this chapter and verse from a fitter at a job I was on recently.
Cant help feeling they're being over conservative and that its partly a legacy thing. There are still quite a few WPD fitters who started their careers with SWALEC long before privatisation. On a job I was doing recently (domestic, nothing particularly special), I fitted 25mm tails and 16mm earth as per. An older WPD guy came along, said "THAT'S good", connected up and then renewed the old cambric tails between cutout and meter (about 10-16mm in old money) with new 16mm (modernish Henley cutout, 80A).
I was amazed!
Certainly, down here in the WPD area (old South Wales Electric), they only fuse to 80A, and balk most definitely at the idea of a 100A supply - according to company policy they will not fit 100A as they reckon the cutouts (modern ones that is) can't take it on a sustained load. I had this chapter and verse from a fitter at a job I was on recently.
Cant help feeling they're being over conservative and that its partly a legacy thing. There are still quite a few WPD fitters who started their careers with SWALEC long before privatisation. On a job I was doing recently (domestic, nothing particularly special), I fitted 25mm tails and 16mm earth as per. An older WPD guy came along, said "THAT'S good", connected up and then renewed the old cambric tails between cutout and meter (about 10-16mm in old money) with new 16mm (modernish Henley cutout, 80A).
I was amazed!
I was going to say that.
No really, I was, but I decided not to in case people thought I was taking the p***.
WPD are my DNO and have long said that 80amp is the max for a standard head - They use a different type of head for 100amp, and anything above this uses the large Lucy heads with CT metering (until recently when they now use an all in one cutout/CT chamber/Meter/customer busbars).
A typical 100amp WPD supply:
A typical 100amp WPD supply:
Thanks for all the replies and sorry for taking so long to get back.
Well the circumference of the smaller tail is 32mm
32mm / 3.142 = 10.18
Diameter = 10.18 / 2 = 5.09
CSA =Pi X R2
3.142 x 25.9 =CSA 81.4 ???
And sorry about this but these three radials on 30 amp fuses, what size cable do you think it is. The far right appears to be a bit thicker.
Many thanks
View media item 18884 View media item 18885 View media item 18886
Well the circumference of the smaller tail is 32mm
32mm / 3.142 = 10.18
Diameter = 10.18 / 2 = 5.09
CSA =Pi X R2
3.142 x 25.9 =CSA 81.4 ???
And sorry about this but these three radials on 30 amp fuses, what size cable do you think it is. The far right appears to be a bit thicker.
Many thanks
View media item 18884 View media item 18885 View media item 18886
Are you measuring the outer circumference, or the circumference of the actual copper - as if you're using the outer one then you're mistakenly including insulation in your calculation.
Also, your calculation would only be valid if the tail was solid copper, as it is almost certainly a number of strands of copper twisted together, the CSA will be significantly less...
Also, your calculation would only be valid if the tail was solid copper, as it is almost certainly a number of strands of copper twisted together, the CSA will be significantly less...
measurement is including sheath, and conductors are of cause stranded.
I would say from left to right, 4, 4, 4, 6.
I'm really not sure that you should be changing CUs just yet....
Did you know that the main switch terminals are live, even when the main switch is off? Those big, brass, exposed terminals with no cover.
I wouldn't take a steel measure near them if I were you.
Did he not turn off the external isolator?
You know - the one he'll be using to make it safe to change the CU.
You know - the one he'll be using to make it safe to change the CU.
DIYnot Local
Staff member
If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.
Select the supplier or trade you require, enter your location to begin your search.
Are you a trade or supplier? You can create your listing free at DIYnot Local
