I have just fitted a replacement main circulation pump to the above slimline dishwasher
(previous motor allegedly seized) and although it fills and drains ok as soon as the main pump is activated it only
runs for 10sec or so and then stops.
Water levels are good.
If I open and close the...
Take the lid off and see if either thermostat has triggered.
you will see the condenser unit on top of the drum-fan housing back right,
thermostats middle front.
I think there are two elements on this model.
-you can also check the resistance on these with a meter to see of they are o/c ie...
Have you checked the continuity on the pressure switch with a meter ie if it clicks you should get a closure on the contact pairs?
It could be a fault with the control board.......not the switch
Replacement latch is p/n 187185 and is listed at £1.39 on the Neff support site no doubt plus the dreaded and postage........
https://www.neff-eshop.com/eshop%28bD1lbiZjPTA2MA==%29/neff/gb/prodp.htm?prod=S5443X2UK%2f01&ESHOPTYPE=A
It is likely held in place by lugs in the casing which will...
It is fairly easy as you can get a socket on the mounting bolts through the
back and then withdraw the motor from underneath (with the machine tipped forward)
For an engineer its much quicker as he only has to remove the one screw
rather than a dozen to do the same thing......
You need to remove the rear panel-prob about a dozen or so Torx screws
(T20/T25) Usually 2 either side centrally are larger ones.
Easier to get at the motor if you lean the machine against the kitchen unit
at 45 degrees.
Remove belt
Remove the two 12mm motor supporting bolts
Remove...
I have replaced a few of these -cut the old one and solder the new one.
Watch out though f the armature is damaged in any way it will wear the new brushes away in a few days and back to square one.....
You can some help on schematics from the Bosch support site
https://www.bosch-eshop.com/eshop/bosch/gb/prodp.htm?prod=WFX3268GB/23
Model code can be enetered in the top right search box
to your problem
You may have a partially blocked tube to the pressure switch which would
cause...
Just an update to say that I have fixed the problem at last!
On closer investigation I discovered that the vent pipe that runs from the
antisyphon drain chamber back to the soap box was leaking.
Overflow only happens when the pump is running at its fastest so any water
ends back in the...
Leccy thanks very much for your input.
I have investigated some more using the Megger I have.
Applying 500V and monitoring at the plug I have noticed that with the
motor disconnected and everything in or out of line apart from the motor gives >3GOhm.
With the motor in line and then...
Thanks for the reply.
The last thing I tried was swapping the motor and then starting a cold wash.
The dials clicked round,then the door light,then the drain pump had a go for for a few seconds and then it tripped.
I think it is tripping as soon as the motor starts to turn the drum...
Hi
I have been trying to fix a WFF2000 which had a faulty element.
The machine would previously wash,drain and rinse etc but would abort
all wash programs before rinsing with the prewash light flashing twice.
The element was O/C so I have replaced it with a new one and thought job done...
The picture shows the gunge in the top of the matrix which is a result of
occasional overflow from the waste outlet and has little to do with your issues.
A nice warm humid environment for all kinds moulds to develop....
If it drains out then your problem is lack of flow through the...
Does the machine reset and pump out water?
If it resets and then doesnt fill then you either have a failed inlet water valve
(rare) jug impellor(common) or a clogged up pressure chamber and transfer pipe(very common)
Can you hear a humming as soon as the machine is switched on?
If so...