Recent content by ron99

Ive knocked the plaster off the chimney breast down to bare brick for the new woodburner, the 100 year old bricks are in great nick, after cleaning I'm gonna get someone in to point the brickwork, what shade of mortar mix would look the best in the newly pointed interior brickwork? thanx

Just taken early retirement and decent at diy. my question is would it be too difficult to remove my timber french doors, attached side windows and the frames and replace with Upvc assisted by my big strong son. any specialist tools required? I already own an extensive diy tool kit.

Im about to lay floor panels in my loft after renewing the insualtion but right across the centre at a right angle to the floor joists if a length of 2 x 1 timber. This runs the whole width of the loft and is nailed to the floor joists. Can this be removed so i can achieve a level floor...

So I would restrict the flow on the 15mm fed rads with their lockshield valves? How will I be able to tell that the 5 groundfloor rads are balanced properly. ta

I have 5 rads groundfloor. if I cut out the 22mmx22mmx10mm tees and replace with 22mmx22mmx15mm on 2 rads would it affect the flow at all on the 3 remainding 10mm fed rads? would I need to balance the flow on the lockshield valves and if so which ones? Thanx

The radiator im about to replace has 10mm copper tube feeding it. For aesthetic reasons i want to replace the 10mm copper with 15mm chrome tube for the new rad. I have a 22mm main under the floorboards groundfloor reducing to 10mm to the rads. Would it be ok to have 22mm (existing) to...

I have a toilet that has no access to the underneath fastenings of the seat without removing the whole thing. The seat needs renewing but im finding my local diy outlets dont stock a top fit seat....(tried all local) Does anyone know the best place to get one online or instore and what...

When the double socket is fixed to the wall what would be the best method of creating a channel for the wiring to drop to the subfloor area. Can i do it without removing the skirting board as i've just decorated. thanx.

I have sanded my ground floor floorboards and would like to insulate from below to retain heat and stop draughts. I have access to the subfloor with room to work and would like some advise on what method to adopt for best results without excessive costs. thanx

Stripped the wallpaper off the walls and now i want to paint them. Which filler should i use to repair the small holes and cracks in the plaster? when i go to b&q there are dozens of fillers. Any other preperation tips that would be useful to me before painting?. walls look in decent nick...

Thanks for the advise. So it seems i can remove the seat from above without having to have access from underneath to hold anything, shame i have to change out seat just for a broken support plastic. when i loosen off the screws the seat will come out no prob, so i guess i need a new seat with...

One of the white plastic cushioning supports on the underside of the seat has broken into bits, so when you sit down the seat slews to one side. Can I purchase these supports anywhere?. If not How do you fit a new toilet seat to a toilet which has only two holes in the top and no access from...

Hi, My sons shower will not turn off, its located in the main bedroom of a barrett house built in 2002. It is a Hydramax (aqualisa) model and he has been told he needs a new cartridge. Problem is in the meantime how does he isolate the shower water supply. he has had to turn the main off to...

thanx for the advise everyone. yes it was a high fault current which found a bad neutral wire and made it open circuit. in loft above bathroom. said offending wiring getting rewired tomorrow. thanx again

thanx for the reply. should i go around the upstairs rose connections to look for a bad joint that has gone open circuit?, is that were i should look? Should i see some kind of witness marks on the joint? should the fuse have blown first? Uncle who is a spark is coming down tomorrow...