Recent content by stagman

  1. S

    22mm pipe to 3/4 compression fitting

    Thanks for all the help, I was suspicious so I bought some imperial olives today in anticipation. I am told they used to be coloured with a green ring for id purpose, hence the name.
  2. S

    22mm pipe to 3/4 compression fitting

    Many thanks. Looks like a compression coupler then with a 3/4 olive. Toolstation also sell end feed couplers but I don't want a bag of 25 which is what they seem to sell.
  3. S

    22mm pipe to 3/4 compression fitting

    Hi I need to connect a 22mm pipe into a 3/4 compression 'T'. I haven't disconnected it yet but I am suspicious that the 22mm pipe won't go through the end nut on the compression fitting. Can I use the end nut off a 22mm compression fitting a. Will a 22mm pipe go into the 3/4 fitting and...
  4. S

    Cast iron panel radiator output

    Not sure what +1 means but many thanks guys, my course of action seems to have been decided!
  5. S

    Cast iron panel radiator output

    I need to replace my central heating system and currently, the radiators are flat panel cast iron radiators, 60 cm high, some three section (120cm), some four section (160cm). I need to decide whether to keep these or replace with steel ones but I need to know what the heat output of the...
  6. S

    Connecting bathroom heated towel rail

    The FCU will be spurred from the ring which is RCD protected - I have tested it by means of its button but I guess the guy who connects up will be able to do so if necessary. I'm surprised the flex going through the wall withouth a plate is permitted , not for any particular reason, it just...
  7. S

    Connecting bathroom heated towel rail

    I have an electric towel rail in the bathroom (zone 2) but it needs connecting. There is an FCU outside the bathroom ready, directly behind where the towel rail is situated but the flex from the rail needs to run to the FCU. Is it permissable to run flex just through the wall or is a flex...
  8. S

    Flat roof dormer

    Anyone any ideas about how much this should cost, roughly?
  9. S

    Flat roof dormer

    The cost is for just the new dormer. Does that seem reasonable? I don't think the architect realised the exising ones were zinc. He just specified lead as that is presumably the best.
  10. S

    Flat roof dormer

    I am having a dormer window installed and this has a flat roof. The plans specify code 5 lead but I am considering zinc as I have two existing dormers which are covered with zinc and seem perfectly fine. I have checked with the local building control and they are happy with that. The flat...
  11. S

    Mondeo 2004 TDCI Car wont start,engine mgt light Glow plugs

    Ask on the talkford forum for the type (it will be delphi). You can pick them up on ebay also, usually the seller will know which engine they are suitable for.
  12. S

    Mondeo 2004 TDCI Car wont start,engine mgt light Glow plugs

    Look around the net, masses of info on this fault as it is so common. Just been having a load of grief with mine, similar problem but also quite a lot of causes. Try these sites. http://www.ilexa.co.uk/forum/index.php?board=20.0...
  13. S

    ford focus cooling fan

    Has it always done it? Could be wiring fault. It is probably fed via a relay so find the appropriate one and pull it out to see if it stops the fan.
  14. S

    Bathroom extractor fan - is fuse necessary?

    You are quite right - the electronics industry fuses everything individually with an appropriate fuse. It's all part of the backyard clearing exercise for when the lawsuits come along.
  15. S

    Bathroom extractor fan - is fuse necessary?

    Thanks for the replies. Looks like I will have to put in the extra FCU for the sake of a 2A reduction, with more cable junctions comes possible future weaknesses.
Top