Recent content by TEX24

  1. T

    Texecom 24 - PIRs Preventing Arming

    Whoopee!! I have a superb fully working Texecom system. I can recite the Texecom installation manual off by heart but I still do not understand how it works. just a note about importing profiles from defaults or third parties. If you have correctly addressed two keyboards to your panel and...
  2. T

    Texecom 24 - PIRs Preventing Arming

    To all those who replied to my post thank you. I know that i did not reply to all of them but i needed to focus on one line of action which for a newbie was quite intensive. The fault has been cleared now and for those interested enough i will report back after walk tests and part arm etc are...
  3. T

    Texecom 24 - PIRs Preventing Arming

    Truly I have just sent the pics and restored the PIRs Appreciated thank you
  4. T

    Texecom 24 - PIRs Preventing Arming

    Would you give me a little time to send pics i now have so many profiles that I need to ensure the correct ones are sent and I have to revert PIRs back to original fixings as the solutions seem more promising. Will also send A diag showing the placement of all relevant components.
  5. T

    Texecom 24 - PIRs Preventing Arming

    WOW i did not expect you to be about so late. I needed to give my head a rest and wind down as I could not get Guard Access out of my mind previous night preventing me getting off to sleep. Thank you i will send pics right now 06-00 am here.
  6. T

    Texecom 24 - PIRs Preventing Arming

    Yes prob is still the same. i have started to redirect the PIRs away from the keyboard but can restore them to the best location if a software solution is possible. May I email all the wintex screen prints to you. there are 9 of them small size about 250 Kb total showing all settings. Is your...
  7. T

    Texecom 24 - PIRs Preventing Arming

    ....the guard access is the right zone setting unless you have xchanged the attributes. timed exit, how long is it on timed. I have offered to go through this with you properly one on one and you haven't followed the advice given, you have done your own spin on it...
  8. T

    Texecom 24 - PIRs Preventing Arming

    i thank you for your replies however i suspect that few have actually read my post through. The PIRs are on GUARD ACCESS and yes that is correct but No it does not work as the PIRs are always active and prevent Arming.That is the whole reason i am posting. The door is on Entry Exit. Area is on...
  9. T

    Texecom 24 - PIRs Preventing Arming

    As noted in my first post setting the PIRs to NOT USED solves the problem and the system arms OK however this is not what I want as the PIRs are there to add protection to the KB near the entry door. resetting the PIRs to Guard Access brings back the problem. i have also powered down the system...
  10. T

    Texecom 24 - PIRs Preventing Arming

    Hi, can you help me with an Arming programming question please. Texecom Premier Elite 24. Wintex software. 2 keyboards. One area only Area A. No Area Suites set up. KB1 in final exit /entry zone. Door contact final exit /entry programmed as entry/exit 1, ommitable, Auto rearm. Two PIRs in...
  11. T

    Commissioning a Texecom Elite 24 system

    That is a big help to me secureiam, your knowledge is just what I was hoping to find and is appreciated.
  12. T

    Commissioning a Texecom Elite 24 system

    The zones all show up as working OK in the Wintex diagnostics but I have not walk tested yet as I would like to see it as all OK before doing that. Are You saying that Wintex software has a reputation for problems then? I was hoping to hear from someone with the same problem which would put my...
  13. T

    Commissioning a Texecom Elite 24 system

    Hi I am commissioning a Texecom Elite 24 system. This is my very first installation. It has 22 zones using FSL wiring. It has 2 external keyboards. Also an 8XP External expander and an 8XE internal expander is included. I am using Wintex software to analyse and configure the system. Wintex...
Back
Top