Why am I so inept with wall plugs?
- Thread starter Mander
- Start date
Sponsored Links
Not a science, but it's certainly a knack, which comes with lots of practice. You need to get a feel for it, know when it's going well, know your drill, to get it straight, and know how deep you need to go.
Just drill it the way you've been doing it, but try not to be so careful...
Then you'll have a hole in the wall big enough to put the toilet roll in ..
Then you'll have a hole in the wall big enough to put the toilet roll in ..
- Joined
- 28 Sep 2020
- Messages
- 150
- Reaction score
- 29
- Country
#drilljedi lol
Sponsored Links
It also really depends on the wall.
In my parents extension built with modern lightweight blocks, mounting stuff on the wall is a breeze. In my property and the rest of my parents property which are built out of tock hard brick with wide joints full of sand-like mortar it's a nightmare.
In my parents extension built with modern lightweight blocks, mounting stuff on the wall is a breeze. In my property and the rest of my parents property which are built out of tock hard brick with wide joints full of sand-like mortar it's a nightmare.
Use The Force, young Skywalker...but not too much.
SDS drill and decent bits. The cheap plastic plugs- i usually use 5mm bit for the reds and 7mm for brown. That usually gets a bite except in ancient lime mortar
Just fitted 8 kitchen wall units and first time ever i did not hit any soft mortar, all holes were in brick but there was one area where the drill was going in as normal and was producing brick dust but then got to about 30mm or so and the drill refused to go any deeper, - in a number of places in that area. I was aiming for 65mm for the ficher douoplugs - which I tried and thought they were great by the way.
I brought that bosh one and its very good but too short.If 30 quid is too much for a set of bits - understandable - then you only neeeeed one - this one:
It's 4mm, which will start you precisely, where you want, in anything, with a diy drill and often without a hammer. It'll be a revelation.
Bosch Expert CYL-9 Multi Construction TCT Drill Bit
A multipurpose drill bit from the Bosch EXPERT range that excels with almost any material used in interior fitting work. Soft concrete, masonry, brick, cement asbestos, ceramics and tiles, softwood, plastic, sheet metals, aluminium – none of them are a problem for this impressive bit.Designed...www.toolstation.com
Who cares if the job takes you a minute longer?
Cheap masonry bits are a pain.
- Joined
- 22 Aug 2006
- Messages
- 5,369
- Reaction score
- 602
- Country
At one time I had several renters and was doing far too much in them. I accumulated just about every type of wall fixing available, because no two walls were the same. Be wary of SDS drills. I remember using one with a 6mm bit. It was a single internal brick wall. The drill just knocked the brick out of the wall.
I never found one single solution for all cases, but making a small pilot hole first never does any harm except to take longer.
A short sharp drill is ok, the hole it drills is a very good guide so they're never "too short".
And yes as someone said, sometimes the only way is to use a ridiculously long fixing, to get a strong-enough hold.
I never found one single solution for all cases, but making a small pilot hole first never does any harm except to take longer.
A short sharp drill is ok, the hole it drills is a very good guide so they're never "too short".
And yes as someone said, sometimes the only way is to use a ridiculously long fixing, to get a strong-enough hold.
DIYnot Local
Staff member
If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.
Select the supplier or trade you require, enter your location to begin your search.
Are you a trade or supplier? You can create your listing free at DIYnot Local
Sponsored Links
