Hi, I currently have two outside lights, each with a PiR sensor. They have developed a fault so that the sensor only works some of the time. At the moment, one is master to the other slave (i.e. one sensor turns on both lights). From this, I assume there must be a spare 'hot' wire between the two, to carry the sensor-switched power. I would like to replace these and reconfigure it so that I have two masters - i.e. either sensor can light both lights. Can somebody please advise on the wiring configuration? Ideally with a picture/diagram. Thanks KK.
Dual master/slave outside lights
- Thread starter klaus_k
- Start date
-
- Tags
- pir sensor wiring a light
Sponsored Links
3 CORE AND EARTH between the two lamps which may very well already be connected as shown above.
I've also added the wiring if you have or require an override switch in purple. Ignore that part if you don't have it.
I don't know the colour of your wiring, I guess you can interpret that or we'll help.
- Joined
- 27 Jan 2008
- Messages
- 23,707
- Reaction score
- 2,671
- Location
- Llanfair Caereinion, Nr Welshpool
- Country
A PIR needs power to work, some pass current through the bulb, some use batteries, and some have a neutral. Also they need to connect and some are wireless, and some use wires. Also controls, they can have LUX, Time, and Range, but some don't have all functions, and use blanking bits to stop activation from selected areas.
In the main stand alone PIR's can be connected in parallel so either will activate both lamps, but some built in types can't run in parallel. It depends on which you select.
In doors switches also vary, with smart switches they can often be programmed with dusk and dawn, but again they need power, three methods to power them, through the bulb, using a neutral, or a battery. The through the bulb type can't power a PIR as once PIR switches off they loose power. I use Tapo (TP-Link) which have batteries so can be programmed to turn on at dusk and off a 11 pm so cats etc don't set them off in middle of night.
I do find dawn is a problem, as switch on at 6 am and off at dawn clearly will not work when dawn is before 6 am. I do have one PIR lamp also switched with smart switch, but in the main have given up with PIR's as too easy set off by cats or other wild life, and would switch off at most inopportune moments. Hands full of shopping and can't even see where to put shopping down.
But I have 8 outside lights, 6 with smart controls, so I switch them on with phone and off with voice command.
In the main stand alone PIR's can be connected in parallel so either will activate both lamps, but some built in types can't run in parallel. It depends on which you select.
In doors switches also vary, with smart switches they can often be programmed with dusk and dawn, but again they need power, three methods to power them, through the bulb, using a neutral, or a battery. The through the bulb type can't power a PIR as once PIR switches off they loose power. I use Tapo (TP-Link) which have batteries so can be programmed to turn on at dusk and off a 11 pm so cats etc don't set them off in middle of night.
I do find dawn is a problem, as switch on at 6 am and off at dawn clearly will not work when dawn is before 6 am. I do have one PIR lamp also switched with smart switch, but in the main have given up with PIR's as too easy set off by cats or other wild life, and would switch off at most inopportune moments. Hands full of shopping and can't even see where to put shopping down.
But I have 8 outside lights, 6 with smart controls, so I switch them on with phone and off with voice command.
Sponsored Links
Please don’t try and replace them with modern LED PIR lights and many don’t give you access to the SL
What sort of areas are you trying to illuminate?
What sort of areas are you trying to illuminate?
SL = switched live
- Joined
- 27 Jan 2008
- Messages
- 23,707
- Reaction score
- 2,671
- Location
- Llanfair Caereinion, Nr Welshpool
- Country
Yes agreed, that is a very common method though.
Of course if not this type then come and ask further.
Stretching the question a bit (sorry). This is the light that got delivered - which does not officially support a master/slave configuration 
Would it make sense to take a tap off the red/black junction and use this to provide this facility? This would cause the PiR controlled 'live' to be shared between two units. The only risk I can see is overloading the wattage of the PiR switch, but the manual says that the maximum power consumption is 2x50W (i.e. 100W total) and each unit will be using 2x3W LED GU10 bulbs (12W total).
It looks like live is fed through the PiR switch to the bulbs (brown/red). Neutral splits with one side going to the switch and the other to the bulbs (blue/white). Earth goes directly to the metal casing.
Would it make sense to take a tap off the red/black junction and use this to provide this facility? This would cause the PiR controlled 'live' to be shared between two units. The only risk I can see is overloading the wattage of the PiR switch, but the manual says that the maximum power consumption is 2x50W (i.e. 100W total) and each unit will be using 2x3W LED GU10 bulbs (12W total).It looks like live is fed through the PiR switch to the bulbs (brown/red). Neutral splits with one side going to the switch and the other to the bulbs (blue/white). Earth goes directly to the metal casing.
Attachments
I personally have done exactly that a number of times and so far without any issues or promlems.Stretching the question a bit (sorry). This is the light that got delivered - which does not officially support a master/slave configuration
However I hope you understand that I can't state is will be safe or work for every PIR fitting.
Thanks @SUNRAY. If it doesn't work then tbh I haven't lost much - I can't seem to find any outdoor lights that officially claim to support master/slave. I'll leave it a day in case @ericmark @Murdochcat or others chime in with a scary warning. Absolute worst case that I can see is that the thing catches fire and burns the house down, but that scenario seems unlikely - it would apply if the 2x50W rating was exceeded too, and it is in a stainless steel case.
It's not really a master and slave arrangement, is it?
It is two masters operating the same two lights. If only one master is activated, it does not operate the other.
It is two masters operating the same two lights. If only one master is activated, it does not operate the other.
DIYnot Local
Staff member
If you need to find a tradesperson to get your job done, please try our local search below, or if you are doing it yourself you can find suppliers local to you.
Select the supplier or trade you require, enter your location to begin your search.
Are you a trade or supplier? You can create your listing free at DIYnot Local
Sponsored Links
