Search results

version 8.2 im using, trying to connect over network as i have the comip hard wired option also trying to connect via the iphone app

still got the same issue with version 8 of wintex. "Connection with control panel could not be established - Please check settings and try again!"

Can’t get in via winter. Used to be able to but when using the same wintex creds it says can’t connect

I’ve tried to do a factory reset by opening the lid, turning off mains and disconnecting battery, turning on power and pressing tamper switch 3 times. Still have the same codes present. So guess it didn’t work.

Found the option in panel and the udl code is what I’m expecting and set to in and wintex

Hi I can’t seem to get into engineer mode now I have 2 codes, one was arming user and one other one an engineer user. When I type in engineer code it was welcome master but when I press 7 I get nothing - when I press menu, there is an option to enable engineer mode which doesn’t really give me...

Hi everyone, got this issue with alarm system Texecom premier elite with the hard wired comic module where I had builders in and they messed up sensor wiring. The panel eventually got locked out and I had to use wintex to enter a code to get another code out to unlock the panel. All worked...

So have connected this up and boiler has 1.5 bar pressure and initially starts up, but when I try and use hot water, it comes up with C6 error code. I can see power going up to the fan, so not sure how bad the damage is…checked 3 fuses on circuit board and they all ok. I’m hoping fan doesn’t...

Thanks - I wasn’t 100% sure but thought it was from other threads

Hi guys - I’ve had some work done and the receiver part of the hive setup has been ripped off the wall. Meaning I have lost all the connections. I have taken pics of the boiler side and have connected up the receiver side part from 1 cable which I’m not sure where it goes? Switch is off atm so...

Thanks burnerman, I know where I’d rather be… So I’ll try that but always the case when I switch to run mode, the engine splutters and cuts out, only runs when the choke is on/carb flap closed. It did start consistently when I had my hand on the throttle and choke forced on, but last time I...

Hi John, a trickle of fuel came out when I took out the plug and pulled about 10times. Plug was kind of wet black. Put back in and still the same after I cleaned up spark plug. Even starting with the accelerator pressed and carb flap closed it still didn’t start up. Binning it isn’t an option...

Hi couldn’t find my spanner to remove the spark but got the strimmer to start consistently by pressing the accelerator with the choke switch down - opposite direction of when I press the lever - starts ok but every time the carb flap opens, it starts to cut out. I’ve tweaked the screws but still...

hi, got the same issue here. i have got a new carb (cleaned out the original one too) spark coming thru (when i have connected spark plug to cabling and spark plug is not connected) new fuel lines new fuel filter on end of fuel line petrol coming into bulb when pressed and flows back ok have...

Thanks - will thin areas crack when the hole is filled?

Hi Over the past few years the floor in garage have eroded Away not sure why but want to patch it up without replacing the whole floor. What can I use to repair solidly that won’t crack easily? Thanks

thanks guys, thats why i mentioned a wet bed of cement/adhesive as that way there should be no gaps. i laid some utility room floor tiles this way at a friends a few years back and it was alot easier than spreading the adhesive using a tool as u drop the tiles on and they all self levelled with...

i'll try and buy the thickest tiles i can get/afford and have rubber mats under workspaces!

thanks flameport. so will plan to use a slc. if i lay the tiles on a wet bed (seen on a few youtube vids) will that work? tiles will be around 7mm thick

Hi, want to hard tile the garage floor rather than soft mat it or paint it. Hopefully make the cleaning of it a lot easier than the rough concrete surface. I don’t think there is a dpm under the concrete but will have to use the SLC to get it all level first. Is there any advice before I put...