Search results

After some heavy downpour on the flu wall my Main brand boiler stopped working and I can see some condensation on the LCD screen and it's flashing with error 110. I can see some water at the bottom of the cover. Any ideas what it could be?

Ahh sleeve nut. just googled that and looks like what I'm after thanks

I'm making a door flap that is to go and sit on a base-plate the two materials will have a hole and i'm looking for something that can go in the hole similiar to a rivet but that will allow the two materials to swing above freely around the hole. I was thinking some sort cylinder with a sort of...

Thanks for the replies. For my friends property, just out of curiousity a small 3 or 4 bed house in London how much should a complete rewire with new consumer unit typically cost London price?

Thanks for that. So just out of curiousity a new build this day and age that has new wiring, eventually at some point will the wiring need changing on that too?

A friend of mine's property has the old fuse wire type consumer unit. Part of building refurbishment to upgrade ceiling lights etc a company is quoting for complete re-wiring to change consumer unit. My question is, with an old system like that is a complete re-wiring needed? Does old wiring...

When attaching plasterboards to blocks using dot and dab, does building regs require the blocks to he rendered first? There is a cavity between block and outside brick with insulation. Just wondering if the internal blocks need to be rendered first? Seems like a waste of time to render then dot...

For the OT connection can I use any cable or does it have to be a certain type of cable? What kind of voltage etc will the OT pins carry?

Looking at the receiver specs of the EPH Combi Pack 4 wireless thermostat, the receiver spec says it's 10(3)A rated. Is that 3A or 10A? what kind of cable should I use to wire it 1mm2 or 1.5mm2?

I've ordered a EPH Combi Pack 4 Wireless Thermostat which I've been told is compatible with this boiler and it's opentherm too. Question regarding opentherm, is there a +/- wire or can the wires from the thermostat receiver's opentherm pins go in any direction to pins 1&2 of the boiler terminals?

So looking at the following installation guide: https://mediacdn.mainheating.co.uk/-/media/websites/mainheating/files/main-eco-compact-combi/main-eco-compact-combi-installation-guide.pdf Page 42, figure 35 seems to show the connections. I've found a wireless thermostat with opentherm...

Will you be able to guide me which page on the user manual refers to installation of the thermostat? From what I understand a thermostat essentially sends a relay activated switched live to the boiler telling it to turn in right? Could you guide me to the wiring diagram on the boiler end if...

A family member just moved into a property that has a new Main brand Eco Compact Combi Boiler which I think is by Baxi, link below seems like this is the one: https://www.mainheating.co.uk/main-products/gas-boilers/combi-boilers/main-eco-compact-combi There seems to be no room thermostats...

I'll measure it and take pics tomorrow. It is probably 12mm by the looks of it. Will it be easier to create the thread using the existing thread as guidance without cutting it short at first and then once I've extended thread then cut it short? As @JohnD said hardest part is the start and...

My existing automatic gear shift stick rod sticks up quite a bit and the gear knob screws on. The gear knob itself is like a nut which screws onto the bolt thread of the rod. I'm thinking if it will be possible to shorten this as there is a big gap between the bottom of the gear knob and the...

I replaced one side gas strut in my boot with a universal type. The length is pretty similar except the new universal one might be a about 8 to 9mm shorter and the stroke is about 10 to 14mm smaller. So on my original strut the stroke is around 210 to 214mm. The new universal strut the stroke is...

Thank you. Is the solid wire inside the electrical solid cables copper? Could I potentially use that from a 2.5mm2 electrical cable and just twist it to tie it up?

Does coat hanger not rust too? I can try that and maybe just dab some high temperature exhaust paint over it to prevent it from rusting lol. I'll give this a shot Thanks

If I was to be able to somehow use a self tapping stainless steel screw to hold up the L plate to the shroud, then all I will have remaining to do is hold the bottom from flapping. I was thinking of drilling a tiny hole and putting something like a paperclip bended back. But if I remember...

Ahh that's what I was worried about. There's not much material so blowing a hole will waste it away lol. Other option is that I could potentially put self tapping metal screw from behind that taps into the metal L plate.