Search results

Something like this? https://www.screwfix.com/p/araldite-2-part-epoxy-adhesive-tubes-opaque-2-x-15ml/2457H I ended up ordering a new pair as one side has stopped working and the other side has moisture in it. strangely the side with moisture is still working but the side with no moisture...

I have a set of chinese bumper reflector LEDs. The front is the red lens and it's glued together with what looks like some sort of clear resin. However, after 1 and half years moisture seems to have made it's way inside the red lens. Even though I applied a thin layer of tiger seal sealant...

I have a Electrolux EOD33002X electric oven. for the oven to work, the clock has to be set. But recently, randomly if the oven main power is left on, The oven just somehow loses power and it resets the clock and starts to make a clicking relay like sound. Only way to make the sound to stop is to...

Anyone?

My property was a new build about 12 years ago when I purchased it. It came with a tile pitch triangular canopy. Like the pic example attached. from the ground to the highest part at the top of the pitch point is about 3.8m high and the width from one end to the other end of the lowest point is...

When my stainless steel sink was put in, it had this rubber sticky pad stuck to the underside of the sink. This pad reduced and dampened the sound when water hits the sink. That pad has over time fallen off and broken loosing it's stick. So I've been living without it but the noise is quite...

I have a strange issue with a light in one room. At first the light briefly worked then it stopped working. I thought maybe the bulb, but then after changing bulb it still was not working. I decided to check the light switch itself and the two wires going to the switch (COM and L1) seem to both...

I've installed laminate flooring and I need to put a theshold in between two rooms where one side is the laminate flooring at about 18mm thick and the other room is just very thin vinyl flooring. So I need a slightly slanted door threshold. I've got the following...

Not sure if this is in the correct section as I couldn't find any suitable section. I have a Blaupunkt BAC-WM-I1212-A05B 3.5k split air conditioner. Been working for good 5/6 years. I had two installed exactly same time. One of them recently stopped working when I put it in heating mode. It just...

I have a little small tea table with wooden legs. The legs screw into a screw that's part of a metal bracket which is screws onto the underside of the table-top. The hole on the wooden leg has worked itself loose and now I'm not able to tighten it. Is there any kind of glue that can bond and...

I'm just not too keen on the idea of having a door threshold there. I've seen installations where the laminate just flows through without a seam joint. Ofcourse under the door frame I will leave a little gap allowing for expansion and contraction.

I wanted some advice on laminate floorin installation for the the following illustration layout. Basically, the direction of the arrows is the the direction i want the full length of the laminate boards. But what i'm wanted to do is have continuation all across from passage to the rooms on the...

Thank you. I've left the existing timer on the always on setting now.

Thank you. All wired up now. The two connections from the boiler to the actual thermostat for controlling the on/off is basically terminal 1 and 2 which by default has a loop wire basically triggering the boiler to always be on unless it's turned off either using timer or the off button on the...

Does the ESRTPRF thermostat have a timer function or can I not switch between the thermostat and built-in timer? Probably won't use the timer and just use the thermostat once that's installed

I have a potterton titanium 40kw combi boiler that doesn't have any room thermostat at the moment, curently it's running on timer. I've got a ESI ESRTPRF wireless room thermostat that I want to wire up. Can anyone help me on how this is wired up to this boiler please?

Batteries could have been pulled out but the Sounders were never installed and invoiced for the job as a completed job. I had a look at the job sheet and the notes, it mentions the installation locations of all smoke detectors and heat detectors and the call point and no mention of any Sounders...

Yes seems like no sounders were ever installed as it's a small shop and I think batteries were originally probably also not installed hence why the wires are going down the bottom by the battery area.

All the companies we've called over just want to rip-off and change a perfectly working system and don't want to even touch this. Seems like a right rip-off. At the same time they are perfecty happy to come and do tests and issue certificates but not willing to make the connection. So my plan is...

A friend of mine has C-tec CFP702-2 fire alarm system in his shop. Recently a dispute led to some vandalism on the fire alarm panel. Basically the front cover was removed and the blue and brown wire that goes to the call point from the panel is disconnected. Picture below. And the batteries were...