Search results

I have a triple vent fan in the loft servicing three wet rooms with each room giving switched live (via room light) to control the fan. I am replacing this fan (not working correctly) with a Envirovent Spider MEVS-H that has one sw live into the fan. Is there a product available that accepts...

Thanks MM Just done a check and there are quite a few suppliers showing out of stock but they will be available soon. How do you rate the app? Does the switch send back info regards state of the switch “on/off or open/closed” My switch will be sited in the metal box on the brick pier using...

Thanks foxhole, whats composite decking?

Please advise, I have made seats in a shower enclosure (2nu seats each comprise three lengths of oroko supported between the tiled walls) I oiled the timbers recently as they were looking dry and now have problems with "staining on the tiles" I should have sealed the Oroko after oiling but...

Good evening, Has anybody used a RTU5024 remote switch? I have electric gates that I want to control from my iphone and I have been quoted £180 for a GSM switch. The RTU5024 seems to give the same requirement but at around £25 Any input appreciated

Thanks

Thanks for all the replies, to summarize I will hardwood dowel (3 X 12mm) and D4 PVA Everbuild glue from toolstation. The two halves sit tight together (dry run) so after I glue it possible to reduce the line of the break that is noticable?

Thanks for the replies, I have the "blue"PVA I also have some two part epoxy resin left (used that for gluing the joints) which would you use? I don't think I will dowel it as the break is in an area on the chair that should not get much force. Re; water ingress and fungal stain how do you...

Sanding an outdoor rocking chair ready for this years varnishing the chair fell off the worktop and broke off part of the back (see pix as was and as is) The wood is sapele. initial thought is to plane / router the two edges square then glue but that would loose height causing a step at the...

My existing boiler is a four pipe with internal diverter valve. The cyl.zone valve (240V) opens it's auxiliary switch and the grey and orange wires from the zone valve connect to the boiler's 24V rail to fire the boiler. The connection between the boiler and the cyl zone valve, 9 mts away, is...

Unvented

Picasso can you send your message again, I read it whilst out (alert on my mobile) now I am back home I cannot retrieve it, your name is there but not the content which did make interesting reading. Thanks

Thanks Ian, It probably explains why Viessmann want a demand box (240V in 24V out) as that box must house the relay you describe. Back in 2002 when I had my boiler installed they didn't bother and it has worked ok ever since.

I have a Siemens zone valve in use on a DHW cyl that is priority demand to a four pipe gas boiler the wiring is configured as follows; When brown is live (240V) the aux switch creates a circuit between Grey and Orange. On my boiler Gr and Or connects to the boiler's 24V DC terminal strip. I am...

Thats sounds expensive are they sending screeders and installers to put it in? I have always used "UFH1" a Doncaster supplier, . If you visit their web page and look at their UFH kits I would presume you need the following, One number eight port manifold (six rooms, incl. utility, have one...

That 30mm isn't going to be an issue with air but if you have concerns give the utility it's own loop (circuit) eight port manifold I have had my UFH in use since 2000 with no issues re; water quality (alway keep plenty of inhibitor in the water.) The insulation thickness generally can be...

Thanks, Meldrews mate The pipework mods, replicating what is at the manifold, would be after that manifolds zone valve that is sited in the plant room and is marked up to distinguish it from the other heating and DHW zone valves on the primary circuit. The existing TMV(s) have no identification...

Hi, Rob some observations on your thread. The position of the manifold is ok but be mindful of the noise from the pump, valves and pipework (where is the boiler?) My son's is in a plant room in the utility with the boiler and cylinder and there is noise / vibration from pipework that resonates...

Thanks Crezzer I have new valve parts that resolve the issue keeping the existing valves in the manifold kits as supplied. To change the TMVs in the manifolds isn't easy because the existing valve bodys are different from alternatives ie, Reliance. There has been issues with the manifold TMVs...

I have two number UFH 12 port manifolds supplying the required heating around the house, both manifolds having issues with the TMVs not giving constant water temp causing the heatmiser room stats to cut out on floor overheat. (don't know the manufacture of the valves only the supplier...