Search results

Its bn down for a week. Was thinking if I used a long flat piece if metal and try break the bond . Or just cut the floor and take it out that way and replace floor. Then angle grind the adhesive to release the board

Hi . Ive a bit of a prob. I have a wbp 18mm plywood floor. I primed a area for my shower tray using srb. The shower tray is a stone resin one 720 x 720 Its slimline profile.about 40mm The floor is level . So I used a 10mm spread of mapei keraflex adhesive. After installing the tray I...

Not fixed yet. Have manflu so everything on hold lol. Will report back when I feel better hopefully in few days

Thanks for replay. The box you can see if a light switch backing. Also straight under the pipe at bottom is a junction box and exteria socket. And a exteria light switch. I was hoping that some barrier polythene layed behind the pipe and full length of wall. Eventually coming out at...

hi 2 questions. im installing new plasterboard, ,i removed the old plasterboard and left the coving at the top without damage. now im about to put a new piece up and below is pipes. what the best way to get the board up under the coving and onto the pipes? is it better to put it...

Cool that's what I want a gpod light coverage . So a 6 watt led . What's the amperage of that . I've a 6 amp fuse on the board. Im currently running 2 striplights in kitchen. 6 60 watt energy jobbies. So I should get aqay with the showee fan/light (40 watts) and the 4 or 5 les downlights

They look good. Saw them on Amazon but out of stock. And cause it's plastic celing panels im installing . They have to b led I saw a led extraction fan It's a hib turbo chrome 3 wat led fanlight

Ahh sp maby separates the way to go . Put exyractor im corner and light in middle. And run the fan of the lighting circuit. Via a fused spur and double pole switch (or a rcd)

Thanks for the replay. What lights have u got . I suppose with tge fan I can site tgat to side of shower cubicle and light in middle . The one candalesen light I got was a energy saving one crap lol

Ive a artexed ceiling with pendulum light. Im fitting shower ect and going tp fit a extractor fan. Should I use one integrated with a light or independently of each other Im also going to install a pvc ceiling ontop of the Artexed one and install led downlights. The room is 8x6, and...

the leads wont reach, was thinking if a multimeter would help

Bump. Anyone any ideas if it's spark modual or what to check. If sparkers knacked wouldI get voltage between the eelecttoids ?

Hi ive a Cambridge double oven s1 . All top burners and both double ovens work fine. But the grill wont ignite, it will light when match at it so its getting gas. Theres no spark jumping between the elecroids. Will it b the actual spark bit or the module. Has anyone fixed one of...

its ment to read 5v , ive noticed a small crack on it and also a cap has burst . cap i can get as it has markings . well the laptop charger will be outputing same voltage 18v 2amps to the charger terminals , so sitting charger on thoes terminals should get start the charging process of the...

its a battery charger for drill battery , parkside one. i was going to doctor the charger with the (i think) laptop charger of same rating . the fet is just blank no markings at all m ive scraped the glure and desoldered it from pcb along wit the heat shield

the Metal Oxide Field-Effect Transistor (Mosfet) is gubbed , its reading zero at the gate , and theres no markings on it to order a new one . so other than get a new charger or fling different Mosfets in at it so thought as both are same spec , that it would do tilll i get info on the...

hi ive a 18v cordless drill , got from lidl, has 2 batteries and has been good. now the charger has died, there's nowt coming out it. lidl guarantee is **** (it don't cover charger) on the charger it says output 2a 18v the a continuous line with broken under it. there's a laptop...

I read its notifiable work , so not gonna go that route, not got loads cash to get it installed, The digital shower is prob a better option, anyone know if this will do my system , or any info on its performance