Search results

I also came to that conclusion but grabbing samples friday. Good point about antibacterial but had a tiled surface for last 5 years and not gone down with anything - and they are worst for harbouring nasties in the grout ! Thanks for a full answer though

thing is, the kitchen has been designed with a range, so i need to be sure it will work, before one is ordered and fitted, if not, i'll need a re-design and a re-think so need to know what is the "correct pressure" needed thanks

Looking to change the kitchen and fit a 6 burner range (with electric ovens) Is there any, like with taps and showers regarding minimum water requirements etc, a minimum gas pressure or volume ? Guy in the shop said gas is gas - only other gas appliance is an 80,000 btu boiler and wanted to...

and here http://www.screwfix.com/prods/50530/Ironmongery/Bolts-Catches/Latches/Touch-Latch-Pack-of-10?cm_re=SEARCHPROMO-_-CATCH-_-50530[/url]

At a price often much greater than supply only. In the case of hillarys, over four times the difference between ordering from their on-line DIY site (weblinds.com) or Hillarys direct (someone comes to your home to measure up, then they fit them) - so if it is truly "free fitting", their sales...

WHAT !!! you serious ! Will go grab some samples next week and put it through its paces !

Continuing from my granite post.... http://www.diynot.com/forums/viewtopic.php?p=976558#976558 Anyone have any knowledge of this material, worked with, use it, benefits, pitfalls etc .... Done a search on here and only two minor references to it.

They've just quoted £2235 for the quarts option and can't highly recommend it enough - started a new thread to find out more

mmm...... max working speed for rasp is 3000rpm your call

I can only imagine it would tear/rip. Think a router is too fast. With a cheap bit, slowest speed and caution, I might be inclined to at least test the theory. How many and how long are these slots to be ? How accurate do they need to be ? What's it for ? additinal...

well had another quote from a company near watford £2167.87 inclusive of fitting and vat !!! the did suggest, however, Quartz ??? "Quartz worktops are made from 96% quartz stone and binding resin agents. Quartz worktops are probably the most durable type of worktop available on the...

the £4,139.19 was all in and inclusive of vat an other recommended suppliers/fitters ?

what you've made is a "gravel-trap" what they use to stop 200mph formula 1 cars ! let alone your run-around ! As above, you need a solid base and just an inch or so of gravel. Not recommended but years ago I had the knock on the door "excuse me sir, we've been working in the area and...

not too bad a guess and to be honest it kinda surprised me. There's little saving on doing any of it DIY so having them do the lot is the way to go. £2,229.72 for the stone £678.00 for cutting & polishing £615.00 for templating & installation £4,139.19 inc or £3,577.78 for topaz gold

just had a quote for this (colour : Nero Assoluto) how much you recon (all-in, templated, fitted, finished) :?:

Well, they do exist and here they are

To be honest, the correct connectors MUST be available (somewhere) and I really don't fancy the hammer, araldite, new thread cutting or solder options :? Thanks

No chance as it has a machined lip to take the 'o' ring and the threads are too close together so two 10mm threads would probably clash. dunno but was told "it aint british mate, get a british tap" useful :-\ Nope, got no tails. This tap "fell off the back of a basin" in a plumbers...

First response from everywhere I've been today, until I produce said tap from my pocket. Definitely 8mm

Need, ideally flexible but ridged will do, M8 thread, 8mm bore with a 15mm compression or tail, tap connector. Where can I get them ?? Got a very small monobloc basin tap, but has an 8mm thread for the tap connectors, which i dont have. screwfix, plumbase, plumbcentre, and two local...